Nargesa MC150B Three-Roll Section Bending Machine

The MC150B is a pyramid-type section bender with three rolls. The two lower rolls feed the stock, and the upper roll position governs the curvature. Nargesa lists round tube capacity up to 50 mm outside diameter. The machine suits furniture arches, hoops and individual curved sections. When ordering rolls for rectangular stock, identify the face that will remain on the outside of the bend. Bending on the wide face and the narrow face calls for different tool and support arrangements. Measure chord and rise after the sample is released. Check the section width at the middle of the arc and the remaining straight length at each end.

Price on request

Manufacturer: Nargesa · Spain

Technical specification

Standard equipment

• Standard rollers MC150B/MC200/MC200H
• Delivered fully assembled

Similar machines

• Section bender · 3 rollers

  Nargesa MC200 Section Roll Bender for Rings and Arcs

  The MC200 is a three-roll bender with two driven lower rolls. A millimetre scale records the upper shaft position. Side correctors guide the stock and can help form helical shapes. For a ring or flange, evaluate how the ends meet after rolling. The drawing should specify the diameter, remaining straight portions and joining gap. For a helix, add the axial pitch and handedness. Nargesa describes nine standard rolls with spacers. Request the roll arrangement for your section, then check flatness and how the ends meet on the trial ring.

  Nargesa

  Price on request
• Section bender · hydraulic

  Nargesa MC200H Hydraulic Section Roll Bender

  The MC200H bends sections on three rolls. The two lower rolls are driven and the upper shaft is adjusted hydraulically. The position scale gives the operator a reference when repeating a batch on the same section. A typical job is a matched pair of arches for a double-leaf gate. Section orientation and the visible face matter as much as the radius. The roll set must guide the section consistently, and both arches should match after the load is released. Give the supplier the cross-section, wall thickness, chord and rise. Assess the sample against a template and check for twist and marks on the visible faces.

  Nargesa

  Price on request
• Section bender · 3 driven rollers

  Nargesa MC400 Section Bending Machine with Three Driven Rolls

  The MC400 drives all three rolls. Independent lower-roll adjustment positions the contact points for the required section and curve. Nargesa specifies a roll diameter of 130 mm. For an exposed stainless tube arch, the surface matters alongside the shape. Select rolls for the tube diameter and finish, and identify the face that will remain visible. Measure the cross-section where the curvature puts the most strain on the tube. Ask for a sample on production stock. Compare the curvature, visible roll marks and the straight portions left before trimming.

  Nargesa

  Price on request
• Section bender · memory control

  Nargesa MC550 Three-Roll Section Bender for Repeat Production

  The MC550 uses three driven rolls and a controller that stores their positions for individual curves. This is useful when arches for canopies, supports or railings return as repeat orders on familiar sections. For a series of matching frames, assess how readily the operator restores the settings after changing rolls. Start with consistent blank lengths and identify where the arc must begin. Nargesa offers a separate CNC kit for more complex transitions. Compare the first and last arches after recalling the saved settings. Record the template deviation and confirm the exact controller and rolls on the quotation.

  Nargesa

  Price on request
• Section bender · memory control

  Nargesa MC650 Section Roll Bender for Long Tubes and Profiles

  The MC650 rolls tubes and sections using three driven rolls and asymmetric lower-shaft adjustment. Nargesa lists round tube capacity up to 101.6 mm with the appropriate tooling. Long stock for greenhouses, canopies and frames needs support because its weight affects how it tracks through the rolls. Plan support points and clearance around the machine for the full part envelope. The control stores roll positions for later runs. Trial the longest section in the job. Check access at entry and exit, then measure chord, rise and twist against the drawing tolerances.

  Nargesa

  Price on request
• Accessory · measuring

  Nargesa Digital Radius Gauge for Bent Tubes and Sections

  This digital gauge reads the inside or outside radius of a bent tube or section. Nargesa lists a 55 to 11,250 mm range when the appropriate one of the three standard measuring arcs is fitted. When inspecting a curved frame, choose the surface referenced by the drawing. Inside radius and section centreline radius are different dimensions. On a profile with transitions, take readings within the zones of constant curvature. To assess the gauge, measure a finished arc at several points and compare the readings with a reference template. Confirm the contact base and repeatability required for your parts.

  Nargesa

  Price on request