Compressors, gas generators and extraction

What a laser workshop needs around the machine: screw compressors, nitrogen and oxygen generators, fume filtration, dust separators and workshop cranes.

• Dust separator

  Weni FD500 / FD700 cyclone dust separator

  The Weni FD500 / FD700 cyclone separates particles from an extraction airstream. Air enters tangentially and swirls inside the body, directing coarser particles toward the wall and down into the collection bin. In a dusty process, the cyclone can act as a pre-separator ahead of fine filters. Choose FD500 or FD700 against the working airflow and available pressure. Allow room to empty the bin and specify downstream filtration for the type of dust collected.

  Weni Solution

  from 3 019 € (≈ 3 379 $) · net, base configuration
• Fume filtration

  Weni WS-TK cartridge dust extraction and filtration

  The Weni WS-TK range extracts and filters dust from industrial equipment. The WS-TK4, WS-TK6 and WS-TK8 differ in cartridge count and airflow capacity. Compressed-air pulses clean the filter cartridges during use. For laser table extraction, specify the airflow required against the duct resistance. Identify the materials being processed and expected dust loading. Include final filtration, the air discharge arrangement and access for cartridge replacement in the layout.

  Weni Solution

  from 10 475 € (≈ 11 723 $) · net, base configuration
• PSA nitrogen

  Weni WS-NG-600 PSA nitrogen generation system

  The Weni WS-NG-600 produces nitrogen from treated compressed air using pressure swing adsorption (PSA). The package can include compression, filtration, drying, buffer vessels and a booster for supplying assist gas to a fiber laser. For stainless parts, evaluate gas purity and edge appearance on a representative cut. Ask for the available flow at the agreed pressure and purity, including peak demand. When comparing with delivered cylinders, factor in electricity, servicing and the laser's operating hours.

  Weni Solution

  from 26 227 € (≈ 29 351 $) · net, base configuration
• PSA oxygen · 25 m³/h

  Weni WS-OG-1500 PSA oxygen generation system

  The Weni WS-OG-1500 is an industrial system that generates oxygen from compressed air by pressure swing adsorption. One application is fiber laser cutting of carbon steel where oxygen is regularly used as the assist gas. Use your cutting schedules to compare laser demand with the package's output. Specify purity, flow and pressure at the machine inlet. Ask the supplier to identify the oxygen-service components and the documentation for integration into your plant.

  Weni Solution

  from 181 144 € (≈ 202 718 $) · net, base configuration
• Workshop crane

  Weni WS-LC270 pillar-mounted jib crane

  The Weni WS-LC270 is a pillar-mounted jib crane for local material handling. A suitably rated vacuum gripper can transfer sheets from a pallet to a laser table. Reach and drive options depend on the work area. Include the heaviest sheet, lifting equipment and gripper in the load assessment as specified by the supplier. Plot the pick-up and set-down points and check reach at both. Confirm the mounting arrangement, power supply and whether the gripper is part of the quotation.

  Weni Solution

  from 3 507 € (≈ 3 925 $) · net, base configuration
• Screw compressor · 16 bar

  Weni AC-20HP-500 screw compressor, 16 bar and 500 L

  The Weni AC-20HP-500 combines a 15 kW screw compressor with a horizontal 500 L receiver and a maximum pressure of 16 bar. It can supply shop equipment, including compatible lasers that use compressed air as an assist gas. Match free air delivery at operating pressure to demand from the laser and other connected equipment. Specify the dryer and filters for the air quality required at the laser inlet. The receiver buffers demand peaks, while compressor output determines how much air is available continuously.

  Weni Solution

  from 7 482 € (≈ 8 373 $) · net, base configuration
• Screw compressor · 16 bar · 380 l

  Aktona 16 bar 15 kW screw compressor with dryer

  The Aktona 15 kW, 16 bar screw compressor is a package for CNC equipment, including lasers configured for compressed-air cutting. Its refrigerated dryer and filters condition the air before it reaches the machine. Size the package for nozzle demand and pressure losses through the air line. Compare delivered flow at working pressure with the most demanding cut. Ask for the actual receiver size, air quality after filtration and service intervals in the quote.

  Aktona

  from 6 308 € (≈ 7 059 $) · net, base configuration