Powder coating booths
Manual booths with cartridge filters, open spray walls, walk-in booths and automatic booths with cyclone recovery – they keep the workshop clean and return the overspray for reuse.
- Manual booth · 2 cartridges · 1.5 kW
COLO-S-1115 compact manual powder coating booth
The COLO-S-1115 is a compact manual booth for brackets, plates and small enclosures. The operator works through the front opening while the filter section collects powder carried past the workpiece. Measure the part with its hook attached and allow space to turn it when several faces need coating. Ask for the usable opening, filter type and count, and the clearance needed to replace the cartridges at the planned installation point.
COLO2 500 $ (≈ 2 234 €) · per unit, delivery not included - Manual booth · 3 cartridges · 4000 m³/h
COLO-1517 manual powder booth with cartridge recovery
The COLO-1517 collects powder through filter cartridges during manual batch coating. It suits parts that an operator can position and coat through the front opening. For single-colour runs, establish how the collected powder is removed and when it can be returned to production. Compare cartridge dimensions, the cleaning arrangement and the service clearance at the rear or side of the proposed booth.
COLOPrice on request - Open booth · 4 cartridges · pulse-jet
COLO-S-3222 open-face powder coating booth
The COLO-S-3222 gives operators a wide front approach to panels, doors and frames during manual application. Choose the part orientation around the faces that must be reached and the position of the filter bank. Tall panels also need space to manoeuvre the hanger in front of the booth. COLO shows several builds in this family. Request a drawing with the clear opening, filter arrangement and required maintenance space.
COLOPrice on request - Walk-in booth · 5 cartridges · 6600 m³/h
COLO-S-3217 walk-in powder booth for heavy parts
The COLO-S-3217 provides walk-in access for manual coating of heavy metal parts. Size the opening around the workpiece and its handling fixture, then check the load capacity along the route to the spray position. Position welded frames so their sides and joints can be reached. Supply a drawing, maximum loaded mass and intended handling method, such as a trolley or suspended carrier, with the project enquiry.
COLOPrice on request - Walk-in booth · 6 cartridges · 8000 m³/h
COLO-3924 large walk-in powder coating booth
The COLO-3924 is a large walk-in booth that gives the operator access around bulky frames, fabrications and long parts. Plan the full route from pretreatment to the curing oven. Include the trolley or hanger when measuring the entrance and leave space to work around the part. Request a layout drawing showing the usable booth envelope, the filter module and the maintenance zones.
COLOPrice on request - Automatic booth · PVC · stainless cyclone
COLO-S-PP automatic plastic powder booth with cyclone
The COLO-S-PP is a plastic booth for an automatic line that changes between colours. Cyclone separation works with the powder supply and automatic guns configured for the project. Describe the colour sequence, expected changeovers per shift and longest production run. Ask to see the wall and powder-path cleaning sequence using your powders. Confirm whether the quotation includes a powder centre, gun reciprocators and the final filtration stage.
COLOPrice on request - Manual booth · one-side open · pulse-jet
Vogamakina VFKW-3 powder coating booth with cartridge filters
The Vogamakina VFKW-3 is a cartridge filter booth for batches of metal parts. The filters collect powder drawn from the working area by the extraction air. Assess the working opening with a typical workpiece on its hanger and check access to every face to be coated. Request the exact VFKW-3 configuration, replacement cartridge size and details of the cleaning and powder collection arrangements.
Vogamakina6 100 € (≈ 6 827 $) · net, delivery not included - Cyclone + after-filter · steel or PVC
Vogamakina cyclone recovery powder coating booth
Vogamakina's modular cyclone booth uses a cyclone followed by a final filter. Powder separated by the cyclone can be sieved and returned to the feed, while finer particles reach the downstream filter. This arrangement suits lines running consecutive batches with planned powder reuse. Specify the booth opening, cyclone service access and the cleaning sequence between strongly contrasting colours when requesting a quote.
VogamakinaPrice on request - Cartridge booth · 2–12 guns · CE / ATEX
Elektrosprey electrostatic powder coating booth with cartridge filters
The Elektrosprey powder booth uses filter cartridges to collect overspray. Select the build around the clear opening and the way parts are hung and turned. State operator count and the colours used in a typical shift. Check cartridge cleaning, collected powder handling and the space needed for maintenance.
ElektrospreyPrice on request - Manual booth · 2 windows · up to 800 g/min
ROMER KPD manual powder coating booth
The ROMER KPD range is designed for manual powder coating. Versions with two working openings and a door let the operator approach a suspended part from different sides, which helps when coating frames and welded assemblies with recessed corners. Compare the opening dimensions with your part and its hanger. Check the clearance needed to rotate the workpiece and the space required to service the polyester filters. Specify extraction airflow and access layout for the selected booth.
ROMERPrice on request - Enclosed booth · from 0.69 kW · 400 g/min
ROMER KPZ enclosed powder coating booth
ROMER KPZ is an enclosed powder booth range for manual coating. On a batch line, booth size affects the space available to hang the workpiece, reach each surface with the gun and transfer the part to curing. Choose a compact or wider version based on the clear opening and loading route. The booths feature automatic filter cleaning. Include the largest part dimensions with its hooks, the handling method and the expected frequency of colour changes in an enquiry.
ROMERPrice on request - Manual booth · door · 2.2 kW
ROMER KPP Powder Coating Booth with Access Door
The KPP is a manual powder coating booth with one operator opening and an access door. The KPP-2 and KPP-3 differ in opening width and filter area, at 30 and 45 m² respectively. For frames and parts with multiple edges, consider how the operator reaches both faces. The opening governs gun access, while the door affects how the hanging fixture is loaded. Trial the booth with the intended powder and a representative part. Check airflow across the working opening and confirm how the automatic filter-cleaning cycle is configured.
ROMERfrom 4 200 € (≈ 4 700 $) · net - Open booth · up to 4 m window
ROMER KPO Open Powder Coating Booth for Panels
The KPO is an open booth with a wide operator opening. The range offers different opening widths, automatic filter cleaning and optional powder recovery. For a fence panel or gate leaf, use the dimensions in its coating position. Show the hanging height and the clearance required for turning. Check gun access to the ends and the back face of the section. Request a booth layout showing your workpiece. On a trial, assess access and powder containment across the full opening at the intended application rate.
ROMERPrice on request - Automatic booth · dielectric · cyclone · ATEX zone 22
ROMER KAP1 automatic powder coating booth
ROMER KAP1 is a dielectric booth for automatic powder application on a conveyor. Part detection works with reciprocators and ProfiSpray A guns so the spray setup can follow the workpiece geometry and how it is hung. Send the minimum and maximum part heights, hanger spacing and any recessed surfaces that need coating. These inputs help specify gun count, reciprocator travel and conveyor speed. For frequent colour changes, include powder recovery and the cleanout sequence in the quotation.
ROMERPrice on request - Manual booth · ClassicStandard / ClassicOpen · 4000–6600 Nm³/h
Gema ClassicLine manual powder coating booths
ClassicLine is Gema's family of manual powder booths for individual workpieces and batches. Select the build around the loaded hanger envelope and access to the different faces of the part. Describe the spray position, number of operators and colour-change routine in the enquiry. Check the clear opening, filter layout and service space on the installation drawing.
GemaPrice on request - Manual booth · 2 cartridges · 3 kW · CE / ATEX
Wagner BASIC 4000 manual suspension powder coating booth
The Wagner BASIC 4000 is a manual booth for individual parts and small batches. Its integrated rotating hook lets the operator reach several faces of a suspended part from the work position. Wagner lists two filter cartridges. Check the sweep of the workpiece when rotated and its mass together with the hanger. For a typical batch, compare how parts are loaded and the space required to replace the cartridges.
WagnerPrice on request - Spray wall · 3 cartridges · 6 kW · CE / ATEX
Wagner BASIC 8000 powder spray wall for larger parts
The Wagner BASIC 8000 is a powder spray wall for manually coating larger workpieces, including parts fed on a manual conveyor. The open working front leaves room to position panels or frames ahead of the filter section. Wagner lists three filter cartridges. Check how the largest part is positioned and whether the operator can reach the required areas. Confirm the conveyor interface and service space around the wall.
WagnerPrice on request - Manual booth · 3 cartridges · 2.2 kW · multi-colour
Wagner ID manual suspension booth for powder coating
The Wagner ID suspension booth is designed for small batches in different colours. A roof-mounted hook holds the part in the working area, and the stainless steel floor and smooth interior are accessible for cleaning. Measure from the hook to the lowest point of the workpiece and check how a batch is changed over. Confirm the powder collection arrangement and filter service clearance in the quotation.
WagnerPrice on request - Spray wall · 3 cartridges · 2.2 kW
Wagner ID powder spray wall for large workpieces
The Wagner ID spray wall serves larger workpieces in long single-colour runs and when shades change frequently. A stainless steel base is part of the working area. Check how panels are fed to and removed from the wall, and where the operator stands to reach their edges. Compare access to the cartridges and the cleaning sequence using the colours your shop actually alternates.
WagnerPrice on request - Compact automatic booth for frequent colour changes
Gema MagicCompact EquiFlow BA04 automatic powder booth MagicCompact® EquiFlow® BA04
MagicCompact EquiFlow BA04 is an automatic Gema booth for lines that alternate between colours. The plastic-panel enclosure and extraction arrangement are designed around cleaning between runs. Supply the part envelope, gun positions and number of colour changes per shift. Specify the powder centre in the quotation and trial the complete changeover with two contrasting powders.
GemaPrice on request - Pre-configured automatic booth for quick colour changes
Wagner QuickCube automatic powder booth for fast colour changes
The Wagner QuickCube is an automatic plastic booth for lines with frequent colour changes. Wagner offers four preconfigured sizes and modular manual positions for coating ahead of or after the automatic zone. Supply the suspended part envelope, gun count and areas requiring manual access. Check how the selected size connects to powder feed, conveyor handling and the changeover cleaning sequence.
WagnerPrice on request - Compact filter booth for small and medium shops
ROMER WP powder coating booth with cartridge filters
ROMER WP is a compact booth range for manual powder application. Cartridge filters collect overspray, Romer Jet cleans the filters and a touchscreen provides booth controls. Compare the WP-3, WP-4, WP-6 and WP-8 by booth size and filter count. To size a booth for your station, specify the widest part, the number of guns in simultaneous use and the clearance available for cartridge service.
ROMERPrice on request - Antistatic plastic booth for automatic lines
Vogamakina fast colour change plastic powder coating booth
Vogamakina designed this plastic booth for automatic coating with frequent colour changes. Antistatic panels and cleaning provisions near the booth floor are part of the manufacturer's described build. Share the number of colours, daily changeovers and longest run when sizing the system. Request a demonstration covering the booth, cyclone and powder centre as one cleaning sequence. Specify which guns, controls and recovery components the line requires.
VogamakinaPrice on request - Through-feed booth with cyclone reclaim for continuous lines
COLO through-feed powder coating booth with cyclone recovery
The COLO through-feed booth is intended for a line where suspended parts enter and leave at opposite ends. A cyclone separates powder from the extraction stream for collection and return according to the line configuration. The layout suits recurring runs of profiles, frames and panels. Specify the largest loaded hanger, carrier pitch and conveyor speed when sizing the booth. Agree on how recovered powder is handled when a different colour enters production.
COLO20 000 $ (≈ 17 872 €) · for 1 piece