ROMER KAP1 automatic powder coating booth
ROMER KAP1 is a dielectric booth for automatic powder application on a conveyor. Part detection works with reciprocators and ProfiSpray A guns so the spray setup can follow the workpiece geometry and how it is hung. Send the minimum and maximum part heights, hanger spacing and any recessed surfaces that need coating. These inputs help specify gun count, reciprocator travel and conveyor speed. For frequent colour changes, include powder recovery and the cleanout sequence in the quotation.
Price on request
Manufacturer: ROMER · Poland
Technical specification
| Body | Dielectric plastic, LED lighting, manipulator slots on both sides |
|---|---|
| Recovery | Pre-filter, cyclone, CP02 powder centre |
| Guns | ProfiSpray A on manipulators, workpiece detection |
| Floor | Programmable air knives |
| Control | 10" touch panel, 50 programs, remote diagnostics, ProfiControl |
| Safety | ATEX 2014/34/EU, II 3D, zone 22 |
| Brand | ROMER (Poland) |
Similar machines
- Manual booth · 2 cartridges · 1.5 kW
COLO-S-1115 compact manual powder coating booth
The COLO-S-1115 is a compact manual booth for brackets, plates and small enclosures. The operator works through the front opening while the filter section collects powder carried past the workpiece. Measure the part with its hook attached and allow space to turn it when several faces need coating. Ask for the usable opening, filter type and count, and the clearance needed to replace the cartridges at the planned installation point.
COLO2 500 $ (≈ 2 234 €) · per unit, delivery not included - Manual booth · 3 cartridges · 4000 m³/h
COLO-1517 manual powder booth with cartridge recovery
The COLO-1517 collects powder through filter cartridges during manual batch coating. It suits parts that an operator can position and coat through the front opening. For single-colour runs, establish how the collected powder is removed and when it can be returned to production. Compare cartridge dimensions, the cleaning arrangement and the service clearance at the rear or side of the proposed booth.
COLOPrice on request - Open booth · 4 cartridges · pulse-jet
COLO-S-3222 open-face powder coating booth
The COLO-S-3222 gives operators a wide front approach to panels, doors and frames during manual application. Choose the part orientation around the faces that must be reached and the position of the filter bank. Tall panels also need space to manoeuvre the hanger in front of the booth. COLO shows several builds in this family. Request a drawing with the clear opening, filter arrangement and required maintenance space.
COLOPrice on request - Walk-in booth · 5 cartridges · 6600 m³/h
COLO-S-3217 walk-in powder booth for heavy parts
The COLO-S-3217 provides walk-in access for manual coating of heavy metal parts. Size the opening around the workpiece and its handling fixture, then check the load capacity along the route to the spray position. Position welded frames so their sides and joints can be reached. Supply a drawing, maximum loaded mass and intended handling method, such as a trolley or suspended carrier, with the project enquiry.
COLOPrice on request - Walk-in booth · 6 cartridges · 8000 m³/h
COLO-3924 large walk-in powder coating booth
The COLO-3924 is a large walk-in booth that gives the operator access around bulky frames, fabrications and long parts. Plan the full route from pretreatment to the curing oven. Include the trolley or hanger when measuring the entrance and leave space to work around the part. Request a layout drawing showing the usable booth envelope, the filter module and the maintenance zones.
COLOPrice on request - Automatic booth · PVC · stainless cyclone
COLO-S-PP automatic plastic powder booth with cyclone
The COLO-S-PP is a plastic booth for an automatic line that changes between colours. Cyclone separation works with the powder supply and automatic guns configured for the project. Describe the colour sequence, expected changeovers per shift and longest production run. Ask to see the wall and powder-path cleaning sequence using your powders. Confirm whether the quotation includes a powder centre, gun reciprocators and the final filtration stage.
COLOPrice on request - Manual booth · one-side open · pulse-jet
Vogamakina VFKW-3 powder coating booth with cartridge filters
The Vogamakina VFKW-3 is a cartridge filter booth for batches of metal parts. The filters collect powder drawn from the working area by the extraction air. Assess the working opening with a typical workpiece on its hanger and check access to every face to be coated. Request the exact VFKW-3 configuration, replacement cartridge size and details of the cleaning and powder collection arrangements.
Vogamakina6 100 € (≈ 6 827 $) · net, delivery not included - Cyclone + after-filter · steel or PVC
Vogamakina cyclone recovery powder coating booth
Vogamakina's modular cyclone booth uses a cyclone followed by a final filter. Powder separated by the cyclone can be sieved and returned to the feed, while finer particles reach the downstream filter. This arrangement suits lines running consecutive batches with planned powder reuse. Specify the booth opening, cyclone service access and the cleaning sequence between strongly contrasting colours when requesting a quote.
VogamakinaPrice on request