Complete lines and pretreatment
Manual and automatic powder coating lines, washing and phosphating before coating, cyclones, powder centres and reciprocators.
- Manual set · booth S-1115 + 6.5 kW oven + gun
COLO powder coating starter set with booth, oven and gun
The COLO starter set brings together a spray booth, a powder gun and a curing oven for manual small-batch work. It fits a shop finishing brackets, plates or compact housings. Measure the largest part on its fixture and check that it passes through both the booth opening and the oven door. Ask for the three model codes, the electrical connection requirements and the supplied powder-feed equipment to compare package quotations.
COLO6 430 $ (≈ 5 746 €) · per set, delivery not included - Manual line · 7 m booth + 7 m gas oven
COLO manual powder coating line for fence panels
This manual COLO line is configured for fence panels, gates and similar long fabrications. Hanging slatted or tubular panels should leave both faces and welded joints accessible. Base oven length and booth approach on the longest panel together with its carrier. Include panels per batch, entrance dimensions and the planned turning or transfer arrangement in the enquiry so the proposed layout matches the workpieces.
COLOPrice on request - Manual line · booth + 5 m gas / diesel oven
COLO manual batch powder coating line for steel frames
This COLO manual line arranges application and curing around batches of fabricated steel frames. It fits a shop handling several frame sizes and changing order quantities. Determine how many frames a carrier can hold while leaving the inside corners accessible. Allow a staging area between the booth and oven, and confirm the batch loading arrangement and any pretreatment equipment included in the quotation.
COLOPrice on request - Manual line · walk-in booth + gas oven · top track
COLO manual powder coating line with overhead track
This manual COLO line moves suspended parts along an overhead track between workstations. It suits frames and welded assemblies that are coated and cured in a hanging position. Provide the combined mass of each part and carrier and the required clearance below the track. Check the oven transfer, staging locations and how carriers accumulate or pass one another in the proposed layout.
COLOPrice on request - Automatic cyclone booth + reciprocator + batch oven
COLO semi-automatic powder coating line for steel plates
The COLO semi-automatic steel plate line combines automatic application with a manually loaded batch oven. Consistent plate geometry makes it possible to plan the gun positions around a recurring workpiece envelope. Decide how edges will be covered and how operators will move coated plates to curing. Provide maximum size and weight, the required face coverage and expected plates per shift to size the line.
COLOPrice on request - Powder feed · ultrasonic sieve · PLC
Vogamakina VM powder centre for automatic coating lines
The Vogamakina VM powder centre manages supply to the guns on an automatic line. In a configured recovery system, transfer equipment brings fresh powder and cyclone reclaim into the feed. Match this station to the booth, sieve and control system. Specify how many guns run at once, how the powder mix is monitored and what is cleaned between colours. Check the supplied pumps, hoses and interfaces against the line layout.
VogamakinaPrice on request - Gun mover · 7" touch · 10 programs
Vogamakina VM vertical reciprocator for automatic powder guns
The Vogamakina VM vertical reciprocator moves automatic powder guns up and down as parts travel through the booth. Stroke and speed are set around part height and line operation. Provide the gun count, total mounting load and useful stroke for sizing. Check hose routing, maintenance access and how the gun motion is coordinated with the conveyor speed in the planned line.
VogamakinaPrice on request - Pretreatment · 2–3 stages · AISI 304
Vogamakina manual spray cabinet for chemical pretreatment
The Vogamakina manual cabinet gives operators a spray station for preparing metal parts before coating. The manufacturer describes an AISI 304 stainless build and two- or three-stage configurations according to the process. Supply the largest part dimensions, substrate, incoming surface condition and rinse requirements. Check how process liquids are collected, how all faces are reached and which utility connections the installation needs.
VogamakinaPrice on request - Spray tunnel · stages to the process
Vogamakina automatic tunnel line for surface pretreatment
The Vogamakina automatic pretreatment tunnel prepares suspended parts before coating. Separate zones are sized around the material and process, such as washing, degreasing and rinsing. For continuous production, zone length and conveyor speed are designed together. Provide the maximum part envelope, substrates, target throughput and site conditions for water and effluent handling. Check which tanks, pumps and controls the quotation includes.
VogamakinaPrice on request - Automatic line · 1–6 m/min · 500–5000 parts/h
Elektrosprey tunnel-type electrostatic powder coating line
The Elektrosprey tunnel line moves workpieces through consecutive stations on a conveyor. Throughput depends on speed, hanger pitch and the time required in each zone. State the substrates, part masses and target pieces per shift. Check pretreatment stages, booth scope and heated oven length against the heaviest product in the mix.
ElektrospreyPrice on request - Pretreatment · 5–9 dip stages
Elektrosprey dip-type metal surface pretreatment line
The Elektrosprey dip line prepares metal surfaces through a sequence of baths before coating. Select the stages around the substrate, incoming contamination and coating requirements. Provide the largest loaded carrier and batches per shift for sizing. Check tank dimensions, transfer, drainage between stages and the site water and effluent connections.
ElektrospreyPrice on request - Cyclone · 10 000–20 000 m³/h
ROMER CK-D low-profile powder recovery cyclone
The ROMER CK-D range separates powder from booth extraction air where available height is limited. A stainless steel hopper, screen and vibrator collect and screen recovered material. An RP-01 connection lets the recovery circuit transfer it back to the powder feed system. For a retrofit, measure overhead clearance and match cyclone airflow and pressure drop to the extraction fan. Where powder is reused, agree on how the hopper, screen and transfer route will be cleaned between colours.
ROMERPrice on request - Turnkey line · washer, dryer, booth, gas oven, 120 m conveyor
ROMER automatic powder coating line
A ROMER automatic powder coating line combines tunnel washing, drying, powder application and curing on an overhead conveyor. In repeat production, the line gives each metal part the same sequence of process stages. Size the line from the part and hanger envelope, target hangers per hour and required surface treatment. Specify the largest frame or panel before selecting conveyor and booth dimensions. At acceptance, check pretreatment results and log the curing temperature on a representative part.
ROMERPrice on request - Pretreatment · manual pressure washing · 11 kW
ROMER MS Pressure Washing Booth for Surface Preparation
The ROMER MS is a stationary pressure washing booth for pretreatment. ROMER offers two- or three-stage arrangements that can include degreasing and phosphating according to the process. For welded frames, identify the contamination to remove and the points that can trap solution. Part position affects access to corners and how it drains after rinsing. Supply the part envelope and typical contamination. Ask for the process stages, solution return arrangement and the water quality specified for the final rinse.
ROMERPrice on request - Automatic corona gun for lines and robots
Gema OptiGun GA04 automatic powder coating gun OptiGun® GA04
The Gema OptiGun GA04 is an automatic powder gun for integration into a booth. Define the target faces, part motion and mounting position before selecting the build. Match nozzle and powder feed to the controller and the planned distance from the part. Ask for a trial on a representative workpiece to assess face, edge and recess coverage.
GemaPrice on request - Gun control unit for automatic lines
Gema OptiStar 4.0 CG20 automatic powder gun controller OptiStar® 4.0 CG20
The Gema OptiStar 4.0 CG20 controls pneumatic and electrostatic parameters for an automatic powder gun. For a retrofit, identify the gun, powder feed and how the central line control selects recipes. Check supplied cables and the cabinet interfaces. Trial two repeat products to confirm that settings can be recalled when production changes over.
GemaPrice on request - Automatic corona gun for coating lines
Wagner PEA-X1 automatic corona powder coating gun
The Wagner PEA-X1 is an automatic corona-charging gun for integration into a powder coating line. Its modular design can be configured with nozzles and accessories for the application. Specify the mount, part geometry and areas to sample. Confirm compatibility with the controller, powder feed and moving or fixed gun support. Ask for a list of nozzles and wear parts for the exact line configuration.
WagnerPrice on request - Automated powder management centre for auto lines
ROMER ProfiCenter CP02 powder feed centre
ROMER ProfiCenter CP02 manages powder feed for an automatic coating booth. Its sealed fluidised hopper takes fresh powder from a box. Depending on the selected mode, recovered powder is mixed back into the feed or routed to waste. Compressed-air cleaning and Modbus communication support integration with the line. For a retrofit, check RP-01 connections, control signals and hose access. If colour carryover is critical, use a dark-to-light changeover trial to assess the cleaning procedure.
ROMERPrice on request - Automatic closed-chamber pretreatment
ROMER Automatic Chamber Washer for Metal Pretreatment
The ROMER chamber washer treats batches using programmed degreasing, rinsing and phosphating stages for the selected process. Its PLC can set treatment times and temperatures. For a batch of brackets, hanger spacing determines whether nozzles reach the inner faces. Give the supplier a section drawing, the intended loading density and the allowed time to drying. Compare parts from the middle and ends of the trial load. Confirm the number of tanks, solution separation and how the solutions are maintained.
ROMERPrice on request - Vertical U-type line for long aluminium profiles
Elektrosprey U-type powder coating line for aluminium profiles
The Elektrosprey U-type line coats aluminium profiles on a route that returns towards the handling area. Size the layout around suspended profile length and separation between carriers on curves. Provide the building layout, maximum part envelope and throughput target. Check loading and unloading positions and the quoted booth, oven and powder feed scope.
ElektrospreyPrice on request - I-beam overhead chain conveyor for paint lines
Vogamakina Webb-type monorail conveyor for coating lines
The Vogamakina Webb-type conveyor carries suspended parts on trolleys driven by a chain along a single rail. The route can be designed with horizontal curves and changes in elevation. Provide loaded hanger mass, carrier spacing and the throughput target for sizing. Check the load rating of the specified chain and the route interfaces at the booth, oven and loading station.
VogamakinaPrice on request - Compact booth + oven set for tyre workshops
Vogamakina powder coating line for car rims
The Vogamakina wheel rim line combines manual booth application with batch curing of a complete set. In the manufacturer's example, the oven takes four 24-inch rims. Rotating hangers give access to spokes and inner rims during application. Specify rim diameter and width, sets per shift and preferred heating source. Agree on how surface preparation will be handled and which stations the quoted package covers.
VogamakinaPrice on request - Automatic gun + control for serial production
COLO-800DA automatic powder application unit
The COLO-800DA controls automatic powder application within a metal finishing line. It suits repeated runs of profiles, panels and frames that pass the guns in a consistent orientation. Map the faces to coat on each pass before integrating the unit with the booth and conveyor. Request a quote detailing gun count, powder feed, individual controls and the interface to part movement. Identify recessed areas that will receive manual touch-up.
COLOfrom 700 $ (≈ 626 €) · per piece, MOQ 1