ROMER SW Burner-Heated Powder Curing Oven
The SW is a burner-heated oven for curing powder coatings. ROMER describes gas and oil configurations selected for the plant and chamber size. For batches of steel frames, compare the complete cycle with the same load. Account for heat-up after loading, the time the parts spend within the powder's cure window and idle time between batches. Confirm the fuel, burner rating and exhaust provisions for the proposed installation. Ask for a trial-cycle record using the intended loading pattern.
from 60 500 € (≈ 67 706 $) · net
Manufacturer: ROMER · Poland
Technical specification
| Heating | Natural gas, LPG or oil burner |
|---|---|
| Insulation | 240–460 mm |
| Control | Thyristor power regulator, touch panel, online diagnostics |
| Variants | SW, SW SPARK (gravity + burner, fluidisation option) |
| Energy | ECO mode – up to 20% lower fuel use (Romer, depends on process) |
| Brand | ROMER (Poland) |
Similar machines
- Batch oven · electric 6.5 kW
COLO-1688 compact electric powder curing oven
The COLO-1688 is an electric batch oven for curing powder on small runs of brackets, hardware and housings. COLO lists working dimensions of 1000 × 845 × 1600 mm in width, depth and height. A fan circulates air through the chamber. Check the height of the tallest hung part and the clear opening needed to load it. Provide your site supply and typical batch mass when requesting a configuration.
COLO2 430 $ (≈ 2 171 €) · per unit, delivery not included - Batch oven · electric 18 kW
COLO-1515 electric powder curing oven with 1.5 m cube chamber
The COLO-1515 is an electric oven with 1500 × 1500 × 1500 mm working dimensions. Its cubic chamber gives flexibility in how compact rims, grilles and housings are arranged. Space the parts so air can circulate through the load. Ask for the clear door opening, hanging layout and electrical requirements for your site. Match the useful oven envelope to the booth and carrier before selecting a complete setup.
COLOPrice on request - Batch oven · electric 18 kW · trolley
COLO-1864 electric powder curing oven with loading trolley
The COLO-1864 electric build with trolley loading handles batches of enclosures, frames and bulky parts. COLO publishes a chamber of 1600 × 1400 × 1800 mm in width, depth and height for the electric model. The trolley lets the batch be arranged outside the oven. Confirm the frame dimensions, payload and rail or wheel layout. Check the connected electrical load and the space needed in front of the door.
COLOPrice on request - Batch oven · electric 40 kW · top track
COLO-2447 batch powder curing oven with overhead track
The COLO-2447 is a batch oven for curing powder on suspended workpieces. With a coordinated track layout, the same carrier can transfer parts from the spray station into the oven. It suits batches of frames and panels of varying heights. Verify clearance below the track, carrier length and the door arrangement around the suspension. When adding the oven to an existing shop, provide the rail interface and current carrier drawing.
COLOPrice on request - Batch oven · electric 54 kW · 4.5 m
COLO-1645 electric powder curing oven with 4.5 m working depth
The COLO-1645 is an electric batch oven for long profiles and frames. COLO lists a 1500 × 4500 × 1650 mm chamber in width, depth and height. Allow for the carrier and clearances around the part when sizing the batch. Plan a straight approach for loading and unloading long parts through the door. Provide maximum batch mass, available supply and the fixture arrangement for a comparable quotation.
COLOPrice on request - Batch oven · gas / LPG · Riello burner
COLO-3210 gas powder curing oven with 3.1 m working depth
The COLO-3210 gas oven is intended for batches of panels and mid-length welded parts. The catalogue working envelope is 2000 × 3100 × 1900 mm in width, depth and height. Use loaded carrier dimensions and the desired time between batches when sizing the equipment. Confirm the gas type, connection and burner maintenance access. Compare quotes on usable chamber size, batch mass and the proposed loading system.
COLOPrice on request - Batch oven · gas · 6 m · two trolleys
COLO 20 ft gas powder curing oven for long parts
The COLO 20 ft gas batch oven is designed for long profiles, fence sections and frames. The manufacturer lists a 6 m working depth and a loading trolley for the catalogue build. Check the carrier length, approach to the door and space needed to withdraw a full batch. Include site fuel, batch weight and required working height so the supplier can quote the appropriate configuration.
COLOPrice on request - Batch oven · gas / LPG / diesel · 3 × 3 m
COLO floor-level walk-in powder curing oven
This COLO walk-in oven is built for loading at shop-floor level. It suits trolley handling of heavy frames or bulky parts into the chamber. Confirm the threshold detail, foundation requirements and wheel loading for the proposed installation. Provide the loaded trolley mass and clear dimensions along its route. Request an installation drawing showing the usable entrance and door arrangement so the oven can be planned with the booth and staging area.
COLOPrice on request