ROMER
Polish manufacturer of powder coating plants: electric and gas ovens, manual and automatic booths, ProfiSpray applicators, cyclones, washers and turnkey lines – with ATEX quality assurance.
About the company
ROMER Group Sp. z o.o. designs and builds powder coating technology in Skarżysko-Kamienna, Poland, on 48,200 m² of production and office space. The company states that it has produced more than 10,000 units and is present in 45 countries, and it holds an ATEX quality-assurance certificate for the manufacture of equipment for potentially explosive zones.
The range covers the whole process. Pretreatment: MS pressure washing stations (up to 200 bar, closed loop, touch panel with saved programmes, RS485 Modbus) and automatic chamber washers for degreasing, rinsing and phosphating with up to five chemical treatments in one chamber. Coating: KPD, KPZ, KPP, KPO and WP manual booths with ROMER JET cleaning, the KAP1 automatic booth, CK cyclone separators, ProfiSpray applicators and ProfiCenter CP02 powder centres. Curing: SL electric, SW gas / oil, SH high-temperature and SR solvent ovens with the iCure logger. On top of that come conveyors and transport systems such as power & free and the modular TR3 traverse, shot blasting machines and complete automatic and semi-automatic paint shops.
ROMER delivers anything from a single booth to a turnkey paint shop, including transport and installation on site, commissioning and training of the customer's staff in operation, and it provides technical support and service through its service department. Its videos show, for example, an automatic line coating welded mesh fence panels with the KAP-1 booth.
Product range
- Electric and gas ovens (SL, SW, SH, SR)
- Manual booths KPD, KPZ, KPP, KPO
- Automatic booth KAP1
- ProfiSpray applicators
- Cyclones and powder centres
- Pressure and tunnel washers
- Conveyors and turnkey lines
- Shot blasting machines
Service and support
Installation, Training, Remote support, Spare parts stock · PL
- Batch oven · electric · forced circulation
ROMER SL Electric Powder Curing Oven
The SL is an electric oven for curing powder coatings. Chamber airflow and the programmable temperature cycle let the shop set a recipe for the workpiece and powder. For fence panels, specify the usable envelope with the trolley or hanging system in place. Thin slats and heavier frames warm at different rates in a mixed load. Assess part-metal temperature against the coating specification. Request the connected electrical load and a heat-up trace for representative parts. Confirm whether the data logger and chamber divider are included.
ROMERfrom 8 200 € (≈ 9 177 $) · net - Batch oven · natural gas / LPG / oil · 240–460 mm insulation
ROMER SW Burner-Heated Powder Curing Oven
The SW is a burner-heated oven for curing powder coatings. ROMER describes gas and oil configurations selected for the plant and chamber size. For batches of steel frames, compare the complete cycle with the same load. Account for heat-up after loading, the time the parts spend within the powder's cure window and idle time between batches. Confirm the fuel, burner rating and exhaust provisions for the proposed installation. Ask for a trial-cycle record using the intended loading pattern.
ROMERfrom 60 500 € (≈ 67 706 $) · net - Manual booth · 2 windows · up to 800 g/min
ROMER KPD manual powder coating booth
The ROMER KPD range is designed for manual powder coating. Versions with two working openings and a door let the operator approach a suspended part from different sides, which helps when coating frames and welded assemblies with recessed corners. Compare the opening dimensions with your part and its hanger. Check the clearance needed to rotate the workpiece and the space required to service the polyester filters. Specify extraction airflow and access layout for the selected booth.
ROMERPrice on request - Enclosed booth · from 0.69 kW · 400 g/min
ROMER KPZ enclosed powder coating booth
ROMER KPZ is an enclosed powder booth range for manual coating. On a batch line, booth size affects the space available to hang the workpiece, reach each surface with the gun and transfer the part to curing. Choose a compact or wider version based on the clear opening and loading route. The booths feature automatic filter cleaning. Include the largest part dimensions with its hooks, the handling method and the expected frequency of colour changes in an enquiry.
ROMERPrice on request - Manual booth · door · 2.2 kW
ROMER KPP Powder Coating Booth with Access Door
The KPP is a manual powder coating booth with one operator opening and an access door. The KPP-2 and KPP-3 differ in opening width and filter area, at 30 and 45 m² respectively. For frames and parts with multiple edges, consider how the operator reaches both faces. The opening governs gun access, while the door affects how the hanging fixture is loaded. Trial the booth with the intended powder and a representative part. Check airflow across the working opening and confirm how the automatic filter-cleaning cycle is configured.
ROMERfrom 4 200 € (≈ 4 700 $) · net - Open booth · up to 4 m window
ROMER KPO Open Powder Coating Booth for Panels
The KPO is an open booth with a wide operator opening. The range offers different opening widths, automatic filter cleaning and optional powder recovery. For a fence panel or gate leaf, use the dimensions in its coating position. Show the hanging height and the clearance required for turning. Check gun access to the ends and the back face of the section. Request a booth layout showing your workpiece. On a trial, assess access and powder containment across the full opening at the intended application rate.
ROMERPrice on request - Automatic booth · dielectric · cyclone · ATEX zone 22
ROMER KAP1 automatic powder coating booth
ROMER KAP1 is a dielectric booth for automatic powder application on a conveyor. Part detection works with reciprocators and ProfiSpray A guns so the spray setup can follow the workpiece geometry and how it is hung. Send the minimum and maximum part heights, hanger spacing and any recessed surfaces that need coating. These inputs help specify gun count, reciprocator travel and conveyor speed. For frequent colour changes, include powder recovery and the cleanout sequence in the quotation.
ROMERPrice on request - Cyclone · 10 000–20 000 m³/h
ROMER CK-D low-profile powder recovery cyclone
The ROMER CK-D range separates powder from booth extraction air where available height is limited. A stainless steel hopper, screen and vibrator collect and screen recovered material. An RP-01 connection lets the recovery circuit transfer it back to the powder feed system. For a retrofit, measure overhead clearance and match cyclone airflow and pressure drop to the extraction fan. Where powder is reused, agree on how the hopper, screen and transfer route will be cleaned between colours.
ROMERPrice on request - Manual unit · box feed · 7" touch · 100 kV
ROMER ProfiSpray V Manual Powder Coating Unit
The ProfiSpray V is a manual powder applicator with box feed and a 7-inch control panel. This configuration suits a shop running short batches and frequent colour changes. On a frame with recessed corners, check film build on both the open faces and the recesses. Use the production powder and hanger for the trial. Time cleaning from the last part in the old colour to the first acceptable part in the next one. Confirm which nozzles and changeover accessories are included.
ROMERPrice on request - Turnkey line · washer, dryer, booth, gas oven, 120 m conveyor
ROMER automatic powder coating line
A ROMER automatic powder coating line combines tunnel washing, drying, powder application and curing on an overhead conveyor. In repeat production, the line gives each metal part the same sequence of process stages. Size the line from the part and hanger envelope, target hangers per hour and required surface treatment. Specify the largest frame or panel before selecting conveyor and booth dimensions. At acceptance, check pretreatment results and log the curing temperature on a representative part.
ROMERPrice on request - Pretreatment · manual pressure washing · 11 kW
ROMER MS Pressure Washing Booth for Surface Preparation
The ROMER MS is a stationary pressure washing booth for pretreatment. ROMER offers two- or three-stage arrangements that can include degreasing and phosphating according to the process. For welded frames, identify the contamination to remove and the points that can trap solution. Part position affects access to corners and how it drains after rinsing. Supply the part envelope and typical contamination. Ask for the process stages, solution return arrangement and the water quality specified for the final rinse.
ROMERPrice on request - Compact filter booth for small and medium shops
ROMER WP powder coating booth with cartridge filters
ROMER WP is a compact booth range for manual powder application. Cartridge filters collect overspray, Romer Jet cleans the filters and a touchscreen provides booth controls. Compare the WP-3, WP-4, WP-6 and WP-8 by booth size and filter count. To size a booth for your station, specify the widest part, the number of guns in simultaneous use and the clearance available for cartridge service.
ROMERPrice on request - Automated powder management centre for auto lines
ROMER ProfiCenter CP02 powder feed centre
ROMER ProfiCenter CP02 manages powder feed for an automatic coating booth. Its sealed fluidised hopper takes fresh powder from a box. Depending on the selected mode, recovered powder is mixed back into the feed or routed to waste. Compressed-air cleaning and Modbus communication support integration with the line. For a retrofit, check RP-01 connections, control signals and hose access. If colour carryover is critical, use a dark-to-light changeover trial to assess the cleaning procedure.
ROMERPrice on request - Automatic closed-chamber pretreatment
ROMER Automatic Chamber Washer for Metal Pretreatment
The ROMER chamber washer treats batches using programmed degreasing, rinsing and phosphating stages for the selected process. Its PLC can set treatment times and temperatures. For a batch of brackets, hanger spacing determines whether nozzles reach the inner faces. Give the supplier a section drawing, the intended loading density and the allowed time to drying. Compare parts from the middle and ends of the trial load. Confirm the number of tanks, solution separation and how the solutions are maintained.
ROMERPrice on request