AONA CNC Punching and Cutting Machine for Four 30 × 30 mm Tubes
This fence and gate configuration feeds, punches and cuts four 30 × 30 mm tubes in parallel. The Machory quotation covers stock up to 6 m long with a 1.5–2 mm wall. The benefit is most relevant when repeated fence parts share the same hole pattern and cut length. The control sets the hole positions and cut length. Specify tooling from the part drawing and identify each face that needs punching so the supplier can confirm the proposed setup. Request a trial using four full-length stock tubes. Check the first and last finished parts for overall length, distance from the end to the first hole and consistency across all four tubes. Time the complete run with feeding and cut-off included.
19 000 $ (≈ 16 978 €) · delivery not included
Manufacturer: Aona Machinery · China
Technical specification
| Tubes | 30 × 30 mm, 1.5–2 mm, up to 6 m – 4 at once |
|---|---|
| Punching force | 80 t hydraulic |
| Punching speed | up to 85 holes/min |
| Accuracy | ±0.01 mm |
| Cylinders | 4 – two for punching, two for cutting |
| Main motor | 15 kW |
| Control | CNC, Mitsubishi PLC, touch screen, 0–100 programs |
| Components | Delta (Taida) servo and reducer, Schneider, Kawasaki pump |
| Tool change | ≈ 10 min |
| Power supply | 380 V, 3-phase, 50 Hz (or to order) |
| Weight | 2800 kg |
| Work environment | Clean, low dust, −15 to 40 °C |
| Made in | Dongying, Shandong, China |
Standard equipment
- 2-year warranty – parts sent free by DHL
- 24-hour online support, operation videos
- Voltage to your country
Similar machines
- Ironworker · 40 t · CNC
Nargesa MX340G CNC 40 t Hydraulic Punching and Shearing Machine
The 40 t MX340G CNC punches sheet, tubes and steel sections. With the relevant tooling it can also shear, bend or form a part. It has a 100 mm vertical ram stroke, a 180 mm throat and ESA S820 CNC control. A jobbing shop could configure it for slots in mounting plates, corner notches or tube-end forming. Each operation needs its own tool. The controller's tool library helps when returning to a saved setup for a repeat order. Choose two parts from current production. Give the supplier the material, thickness, opening shape and distance to the edge for each. Request sample parts and time the changeover between tools.
NargesaPrice on request - Ironworker · 70 t
Nargesa MX700 70 t Hydraulic Ironworker with 350 mm Throat
The MX700 combines a nominal 70 t force with a 350 mm throat and a 160 mm ram stroke. Its 600 × 350 mm table provides room for tooling and support under larger parts. Throat depth matters when a hole sits well inside a broad plate or when a section flange must pass beside the punch. Check the part with the die, holder and fixture installed. Usable clearance depends on the complete setup. Provide a section through the least accessible hole and dimension it from the part edge. If the job includes notching or bending, specify the finished geometry for that operation and ask for the corresponding tool.
NargesaPrice on request - 3 hydraulic heads · fence tubes
AONA Hydraulic Tube Punching Machine with 3 Heads and 5 Dies
Three hydraulic heads and five dies cover different punching tasks in fence and gate fabrication. The quoted package includes a 7 × 12 mm oblong slot in 30 × 30 mm tube and hole layouts to drawing for 50 × 50 and 60 × 60 mm sections. A shop can use different tooling for fence rails and gate hardware. The length stop provides a repeatable datum from the tube end. For a lock, handle or euro cylinder, send the hardware drawings and mark the orientation of each opening on the tube faces. Evaluate one sample from each die during acceptance. Fit the actual hardware to the sample and verify the hole locations on the wall thickness you intend to run.
Aona Machinery12 750 $ (≈ 11 393 €) · delivery not included