Aona Machinery
Chinese manufacturer of tube and profile processing machines since 2000: CNC pipe punching and cutting lines, angle and C-channel punching, pipe saw and roll cutters, tube end forming and thread rolling, rack beam welding machines – most built to the customer drawing.
About the company
Dongying Aona Machinery Co., Ltd. was established in 2000 in Dongying, Shandong Province. It designs and builds machines for tube and profile processing: CNC pipe punching and cutting lines, angle-steel and C-channel punching lines, pipe saw, angle and roll cutters, tube end forming, shrinking and thread rolling machines, pipe benders and automatic rack beam welding machines. Most machines are customised to the customer tube, hole pattern and output.
According to the company the site covers 26 000 m² with a 15 000 m² factory, production capacity is about 2 000 machines a year and at least 10 new products are released every year. In China it has 19 sales and service agencies with 26 service technicians, and machines are exported to more than 50 countries.
Delivery is from the plant in Dongying by sea, with 30% advance and 70% before shipment (L/C, D/A and D/P are also accepted). The warranty is 2 years; parts that fail in that time are sent free by DHL. An Aona engineer can install the machine and train the staff free of charge – the buyer pays the flights, food and hotel – and remote support is available 24 hours a day.
Product range
- CNC pipe punching and cutting lines
- Fence tube punching, arrow and V-notch machines
- Angle steel and C-channel punching lines
- Pipe saw, angle and roll cutting machines
- Tube end forming, swaging and thread rolling
- Flange hole forming machines
- Rack and shelf beam welding machines
Service and support
Installation, Training, Remote support, Spare parts stock · CN · 2 years from the bill of lading / leaving the factory; failed parts sent free by DHL; lifelong technical guidance
- Tube ends · automatic line
AONA Automatic Tube Loading, Swaging and Thread Rolling Line
The line feeds the tube, swages the end and rolls an external thread. AONA lists a base range of Ø10–60 mm with options for the tube size and thread type. A typical part is a tubular handle or pole that screws into a fitting. The reduced diameter, thread length and transition to the full tube need to match the assembly drawing together. Evaluate accepted parts after all three operations. Provide the incoming length, material and wall thickness. Ask for a sample that fits the actual connector and record the changeover time between sizes.
Aona MachineryPrice on request - Thread rolling · Ø3–200 mm
AONA AN-PTR200 Thread Rolling Machine for Tubes and Bars
The AN-PTR200 forms straight external threads on tubes or bars with two rolling dies. Match the roller set to the thread form, pitch and blank size. The hollow drive design provides through-feed for long stock. Confirm the available clearance and support on both sides of the machine, along with the thread length required on the finished part. Have the supplier roll a sample using your actual material. Check the thread with an appropriate gauge and the mating component used in assembly.
Aona MachineryPrice on request - CNC punching + cutting · 10–80 t
AONA CNC Tube Punching and Cut-to-Length Line
This line combines servo feeding, programmed hole punching and cut-off. AONA offers configurations for round and square tubes and other sections with compatible tooling. For mounting members and frame components, the distance from the cut end to the first hole often determines fit-up. Each part family needs a defined die, reference face and starting position. Stored programmes help a shop return to a previous run after a changeover. Submit two representative drawings with different lengths and hole pitches. Request sample parts after the tool change and check the first and last parts of a run against the same drawing tolerance.
Aona MachineryPrice on request - Roll cutting · 6 m
AONA Automatic Pipe Roll Cutter with Hydraulic Feeding
This roll cutting machine cuts pipe to length with automatic hydraulic feeding. AONA lists a length of up to 6 m. Ask the supplier to specify the maximum incoming stock length and maximum finished part length separately. For batches of duct parts, metal furniture or tubular assemblies, evaluate the full incoming stock length. Consecutive cuts need to stay within the length tolerance as the feed approaches the end of the pipe. Give the supplier the incoming and finished lengths and the expected lot size. Ask for a trial on one full stock length, the number of accepted pieces and the size of the end remnant. Confirm how finished pieces transfer to the next operation.
Aona MachineryPrice on request - Cold roll cutting · Ø8–260 mm
AONA Automatic Roll Cutter for Round Tubes Ø8–260 mm
This version uses a rotating roller tool for cold cutting round tubes. AONA lists an Ø8–260 mm range. Wall capacity and the setup depend on the diameter, material and configuration. For short sleeves and spacers, both overall length and the usable bore after cutting matter. Compare samples at the smallest and largest sizes in your job using the actual steel grade and wall thickness. Measure several parts for length, ovality and the condition of the inside edge. Request a feed-to-discharge cycle time for each representative size.
Aona MachineryPrice on request - CNC punching · several tubes at once
AONA Fully Automatic CNC Tube Punching Machine
This automated line produces repeated hole patterns in metal tubes. The CNC sets positions along the stock. AONA offers feeding and punching equipment tailored to the production brief. In a long run, throughput depends on how stock enters the machine and how finished parts are collected. Machory shows a configuration that processes four tubes in parallel. The fixture and the number of positions need to match the actual section and hole pitch. Describe how stock is supplied, how many part types run in a shift and how punched parts are collected. Compare accepted tubes per complete cycle with loading included.
Aona MachineryPrice on request - Rotary cold cutting · 6 m
AONA Automatic Rotary Cold Cutting Machine for Pipe
This machine uses a cutting wheel for rotary cold cutting of pipe. AONA describes versions for steel, stainless steel and other materials, with suitability confirmed for the specific pipe. For a pipe that will receive a coupling or undergo further forming, the inside edge affects fit-up. On galvanised stock, include any coating requirements near the cut. Match the wheel to the material and wall thickness. Ask for a cut made on your actual pipe. Measure the bore around the cut and check the fit of the mating component before selecting the setup.
Aona MachineryPrice on request - Rack beam welding · 2 stations
AONA Two-Station Pallet Racking Beam Welding Machine
Two stations separate handling from welding. While one station welds the beam and its end connectors, the other can be unloaded and prepared for the next part. The arrangement is relevant to regular batches with a steady supply of prepared beams and connectors. Output depends on positioning time, torch time and the station transfer. For mixed lengths, confirm how each fixture is adjusted. Request a timed trial with the stations alternating. Count completed beams over a representative run and check the loading and unloading arrangement at your beam length and weight.
Aona MachineryPrice on request - Shelf beam welding · 4 torches
AONA Automatic Shelf Rack Beam Welding Machine
This machine locates a shelf beam and its end brackets in a fixture for automatic welding. AONA describes pneumatic clamping, length adjustment and configurations with torches working at both ends together. In a batch of shelf beams, bracket geometry affects how each beam fits the uprights. Submit the beam and bracket drawings with the required weld locations so the supplier can match the fixture to the assembly. Inspect the trial beam after it cools. Check bracket spacing and parallelism, then verify fit on the actual rack uprights.
Aona MachineryPrice on request - Rack beam welding · 6 sides
AONA Six-Side Rack Beam Welding Machine
The six-side configuration serves rack beams with end connectors requiring welds on several faces. AONA describes pneumatic clamping and a turnover mechanism to provide torch access around the beam geometry. The weld layout drives the configuration. Send drawings of both ends with the faces, seam lengths and positions marked. Show restricted areas around the connector in section so the supplier can assess torch access. On the trial beam, verify that all specified seam locations are covered and check dimensions after cooling. Compare the time for the full sequence with turnover included.
Aona MachineryPrice on request - CNC punching · 70–120 strokes/min
AONA CNC Tube Punching Machine with Programmable Pitch
Servo feeding positions the tube for regularly or irregularly spaced holes. AONA describes CNC punching for round, square and rectangular sections with dies matched to the part. Consider this configuration when different products start from pre-cut blanks. Two mounting supports can use the same tube section with different hole counts and distances from the end. Stored programmes retain the layouts, while the die determines the hole shape. Run two hole patterns on the same stock during a trial. Measure the first and last hole positions, check repeatability after switching programmes and inspect the tube wall around each opening.
Aona MachineryPrice on request - CNC punching · PVC and metal tubes
AONA CNC PVC Pipe Punching Machine
The PVC version uses CNC control to position holes and set their count. The die and pipe support need to match the plastic grade, outside diameter and wall thickness. On perforated pipes for air or water distribution, regular pitch is only one requirement. Edge quality and preservation of the pipe shape matter as well. Use the same PVC grade intended for production when comparing tooling and clamping proposals. Send a stock sample with the hole layout. Check hole diameter, pitch and pipe ovality on the trial piece. Inspect around the openings for visible stress whitening or cracks.
Aona MachineryPrice on request - CNC punching · round tubes
AONA CNC Round Tube Punching Machine with Rotary Positioning
This CNC machine is configured for round tubes. For parts with holes at different angular positions, a rotary fixture can combine axial feed and rotation in one programme. A typical part has two opposing holes and a third at another point around the circumference. Define the angular datum, the axial position and the alignment required between opposite holes. The clamp and support need to suit the outside diameter and wall thickness. Request a sample covering every position on the drawing. Check the angular spacing and inspect the tube for ovality around the punched openings.
Aona MachineryPrice on request - Hydraulic punching · flatten, punch, cut
AONA Hydraulic Tube Punching and End Flattening Machine
This hydraulic machine punches tubes using interchangeable tooling. Machory shows an end-processing configuration that can flatten, punch and cut on one machine. A representative part is a tubular brace with a flattened mounting tab. Fit depends on the tab width, the hole centre and the orientation of the flattened section. Include the transition from the tube to the flat tab on the drawing so the tooling proposal reflects the finished part. Request a trial part that includes every required operation. Check fit-up and confirm which tools for flattening, punching and cut-off are supplied with the machine.
Aona MachineryPrice on request - CNC angle line · 10–100 t
AONA CNC Steel Angle Punching and Cutting Line
The line feeds and clamps steel angle, punches a programmed pattern and cuts the part to length. The programme defines the pitch, number of positions and feed for each part. Angle brackets and supports can have holes on one or both legs. Mark the datum edge, orientation and first hole from the end. AONA describes a back-pull option for holes close to the end, so identify that feature when comparing setups. Trial the shortest part and the part with the smallest hole-to-end clearance. Measure the hole positions on both legs and verify the overall length after cut-off.
Aona MachineryPrice on request - Hole punching + flanging · 25–80 t
AONA Pipe Hole Punching and Collar Forming Machine
This machine forms a raised collar around an opening in the pipe wall. The collar provides a mating surface for a branch in parts such as duct sections or tubular assemblies. The finished geometry depends on the opening diameter as well as the height and shape of the collar. Provide drawings of the main tube and the mating part so the supplier can match the tooling to the section, wall and material. Measure the inside diameter, height and uniformity of the formed collar. Test the branch fit around the full opening and ask for a sectioned sample if the remaining wall thickness in the formed area is critical.
Aona MachineryPrice on request - CNC punching + cutting · ±0.05 mm
AONA 4-Cylinder CNC Tube Punching and Cutting Machine
This line uses four hydraulic cylinders. Two perform punching and two handle cut-off. A servo feed positions the stock for the programmed sequence of operations. The cylinder count describes how the work is divided. The quoted fixtures and dies determine how many tubes run together, which hole shapes can be made and how close an operation can be to the cut end. Those details make it possible to compare competing configurations for the same part. Provide a drawing with the full hole pattern, part length and tolerances. Ask for the operation sequence and a measured cycle from feeding through to the finished cut piece.
Aona MachineryPrice on request - 90° notching · 20–50 t
AONA Hydraulic 90° Tube Notching Machine for Bending
This hydraulic notcher prepares a tube or profile for folding into a 90° corner. AONA describes tooling for different sections, including square and rectangular tubing. The die must match the section size and wall thickness. For frames made in smaller runs, start with the finished corner and overall dimensions. The supplier needs the bend location and the permissible gap when the notch closes. Those details determine whether a proposed die suits the part. Send the section drawing and the finished corner drawing together. On the trial part, inspect the tube around the notch and measure the angle after folding. Confirm tooling separately for each required section.
Aona MachineryPrice on request - CNC C-channel line · 10–100 t
AONA CNC C-Channel Punching Machine for Steel Profiles
The machine feeds and clamps a steel C-channel for programmed punching. Servo positioning sets the pitch and hole count for repeat parts used in support or racking systems. Profiles with the same external width can leave different tool clearances when they have return lips. Supply the full cross-section, profile orientation and hole map for the web or flanges. Pay particular attention to the hole nearest the end. Ask for a trial on the longest channel in the job. Check cumulative pitch error along the row of holes and verify alignment with the actual brackets or connectors.
Aona MachineryPrice on request - Tube end forming · Ø120 × 5
AONA TM120NC Hydraulic Tube End Forming Machine
The TM120NC is a hydraulic tube end former. The tooling determines whether the end is reduced or expanded. AONA lists PLC control and a servo die change drive for the documented configuration. For a telescoping assembly, specify the diameter after forming and the insertion length into the mating part. Include a longitudinal section of a transition end so the supplier can see where the geometry changes. Request samples of the most demanding size in the run. Measure the formed length and concentricity, then check the fit with the actual mating tube.
Aona MachineryPrice on request - CNC profile punching · up to 120 holes/min
AONA CNC Punching Machine for Steel Channels and Angles
This hydraulic CNC machine uses servo feed to punch steel channels and angles. AONA describes options for stock up to 6 m, subject to the section and the order specification. For a shop with a mixed order book, switching between channels and angles is a key consideration. The different reference surfaces call for compatible guides and dies. A saved programme restores the hole pattern, while the setup must also restore the physical datum. Supply one representative drawing for each section. Time the changeover in a trial and check the first hole positions after restarting with the second section.
Aona MachineryPrice on request - CNC · 4 tubes at once
AONA CNC Punching and Cutting Machine for Four 30 × 30 mm Tubes
This fence and gate configuration feeds, punches and cuts four 30 × 30 mm tubes in parallel. The Machory quotation covers stock up to 6 m long with a 1.5–2 mm wall. The benefit is most relevant when repeated fence parts share the same hole pattern and cut length. The control sets the hole positions and cut length. Specify tooling from the part drawing and identify each face that needs punching so the supplier can confirm the proposed setup. Request a trial using four full-length stock tubes. Check the first and last finished parts for overall length, distance from the end to the first hole and consistency across all four tubes. Time the complete run with feeding and cut-off included.
Aona Machinery19 000 $ (≈ 16 978 €) · delivery not included - Arrow ends + cutting · 2 cylinders
AONA Hydraulic Fence Picket Spear Tip Forming Machine
This hydraulic machine forms a spear-shaped end on hollow fence pickets. The listed setup is for 20 × 20 mm tube with a 1.5–2 mm wall and uses a separate hydraulic cylinder for cutting stock to length. Tip symmetry and finished height are visible across an entire fence panel. Provide the desired outline and formed dimensions so the supplier can match the die to the picket. A manual stop sets the blank length, so the sample run should include both cut-off and forming. Check several pickets for overall length, tip shape and edge condition before comparing offers. Confirm which tube sections are covered by the separate cut-off tool.
Aona Machinery7 300 $ (≈ 6 523 €) · delivery not included - Saw cutting · roller feed · 6 m
AONA Automatic Tube Saw with Roller Feed
Rollers position the tube for a programmed cut on the circular saw. The Machory configuration lists sections up to 100 × 100 mm with walls up to 2 mm and incoming stock up to 6 m long. This is a candidate for batches of straight blanks for panels, frames and stands. Compare the number of usable pieces produced from a full stock length. Account for saw kerf, any initial end trim and the remnant left by the feed system. Have the supplier cut the shortest and longest parts in your usual mix. Measure several consecutive pieces and check end squareness and edge condition on your actual material.
Aona Machinery7 900 $ (≈ 7 059 €) · delivery not included - Angle saw · 0–180°
AONA Semi-Automatic Mitre Saw for Tubes and Profiles
This semi-automatic circular saw makes mitre cuts on metal tubes and profiles. In the quoted setup a pneumatic cylinder clamps the part, then the saw feeds, cuts and retracts. The listed sections run from 10 × 10 to 100 × 100 mm with 1.5–2 mm walls. A typical job is cutting left- and right-hand mitres for a frame. Confirm the usable section size at the angle you need, since the cutting geometry changes with the angle and the orientation of the stock. Ask for a pair of matching cuts in your own section. Bring the ends together and check the joint gap, included angle and edge condition before welding.
Aona Machinery6 500 $ (≈ 5 808 €) · delivery not included - 90° V-notching · 6 dies
AONA Hydraulic V-Notching Machine with 6 Dies
This semi-automatic hydraulic machine cuts V-notches for folding 90° corners in gate and railing frames. The Machory package lists six dies for 20 × 20, 30 × 30, 40 × 40, 50 × 50, 60 × 40 and 60 × 60 mm tube with a 1.5–2 mm wall. On a frame folded from one length of tube, the notch positions determine the finished side lengths. For a 60 × 40 mm rectangular section, identify the face that must be visible after folding and show that orientation on the tooling drawing. Assess the test piece after folding. Check the finished angle, edge alignment and frame dimensions. For repeat production, request several consecutive parts positioned using the length stop.
Aona Machinery12 350 $ (≈ 11 036 €) · delivery not included - 3 hydraulic heads · fence tubes
AONA Hydraulic Tube Punching Machine with 3 Heads and 5 Dies
Three hydraulic heads and five dies cover different punching tasks in fence and gate fabrication. The quoted package includes a 7 × 12 mm oblong slot in 30 × 30 mm tube and hole layouts to drawing for 50 × 50 and 60 × 60 mm sections. A shop can use different tooling for fence rails and gate hardware. The length stop provides a repeatable datum from the tube end. For a lock, handle or euro cylinder, send the hardware drawings and mark the orientation of each opening on the tube faces. Evaluate one sample from each die during acceptance. Fit the actual hardware to the sample and verify the hole locations on the wall thickness you intend to run.
Aona Machinery12 750 $ (≈ 11 393 €) · delivery not included