Fence & gate machines
Lines for 3D and 2D panels, roll forming for lamellas and posts, punching, notching, tips, forged decoration and arch bending – the machines for fences, gates and railings in one place.
Manufacturers: Nargesa, Aona Machinery, DAPU, Sade (LN), Kaiye, IDEAL, Linbay, Yanwu, ZLM (Liming), JCX (Golden Integrity), Xianfa, Zhongtuo
3D and 2D fence panel lines (9)
Automatic lines that straighten wire, weld the panel and bend the V-ribs of 3D panels. The largest investment in fence production.
- Welding + V-bending + stacking
DAPU DP-FP-2500AN automatic 3D fence panel production line
The DAPU DP-FP-2500AN integrates wire feed, welding, servo-controlled bending and stacking for 3D fence panels. Specify the heaviest panel, wire pitches and bend count. At acceptance, follow a full run from wire feed to a finished stack. Verify stack height, bundle outfeed and throughput at your panel geometry.
DAPUPrice on request - Welding · from cut wires
DAPU DP-FP-2500A fence mesh welding machine
The DAPU DP-FP-2500A welds wire mesh for fence panels. DAPU lists a wire diameter range of 3–6 mm. For 3D panels, provide the mesh drawing and bend positions to coordinate welding and downstream bending. During a trial, inspect panel width, mesh pitch and weld quality with the line and cross wire diameters used in production.
DAPUPrice on request - Wire preparation
DAPU GT3-6H CNC wire straightener and cutter for 3–6 mm wire
The DAPU GT3-6H straightens coiled wire and cuts rods for mesh welders. The listed diameter range is 3–6 mm. Specify wire type and the lengths required for line and cross wires. Test straightness and length variation on short and long runs. Match the collection arrangement to the loading method on the welding line.
DAPUPrice on request - Welding + bending + stacking
Sade HLW2500A automatic line for 2D and 3D fence panels
The HLW2500A is the Sade configuration listed for automated production of flat 2D and bent 3D wire mesh fence panels. Specify wire diameters, mesh pitch and the reinforcement bend geometry for each panel. Review the proposed line layout to identify the automated operations and what is involved in changing from one panel type to the other.
Sade (LN)Price on request - Welding + bending · semi-automatic
Sade HLW2500B semi-automatic 3D fence panel welding and bending line
The HLW2500B combines mesh welding and forming the reinforcement bends in 3D fence panels. To specify the semi-automatic line, define the panel dimensions, wire diameters and number of bends over the panel height. Confirm the operator positions, transfers between stations and discharge of finished panels in the proposed layout.
Sade (LN)Price on request - Welding + bending + robot stacking
Kaiye KY-RWM-2500 CNC 3D fence panel line with robot stacking
The Kaiye KY-RWM-2500 configuration listed in Machory is intended for series production of welded 3D panels with robot stacking. Specify maximum panel mass, stacking orientation and bundle dimensions along with the mesh pattern. Check the integration of welding, bending and stacking in the quoted line. Request a demonstration with the largest panel and confirmation of the exact configuration code.
Kaiye68 860 $ (≈ 61 532 €) · per set for 1–2 sets - Welding + bending
Kaiye KY-RWM-2000 welding line for 2 m 3D fence panels
The Kaiye KY-RWM-2000 is a welding line for fence panels with a 2 m working width. For a 3D panel, provide the mesh opening, line and cross wire diameters and positions of the reinforcing bends. Ask for a process layout showing feed, bending and outfeed for the automatic or semi-automatic build. Confirm operator stations and output at your panel size.
Kaiye62 350 $ (≈ 55 714 €) · per set for 1–2 sets - Mesh welding · modular line
IDEAL Type GA modular mesh welding line
The IDEAL GA family can be configured around a particular product, such as a mesh panel, a flat-bar assembly or a wire cable tray. Feed choices and downstream steps, including trimming or bending where specified, determine the line layout. Provide a finished part drawing with tolerances and the expected production mix to size the equipment.
IDEALPrice on request - Mesh welding · medium frequency
IDEAL EasyLineWelder 816 wire mesh welding machine
The EasyLineWelder 816 is IDEAL's standardized machine for welded wire mesh products. Submit drawings with panel dimensions and the diameter and spacing of both longitudinal and cross wires. Use those details to check the working field against the product range and confirm the feed arrangement for the intended run.
IDEALPrice on request
Roll forming lines for lamella fences (5)
Lines that pull sheet from the coil through roller stations, form the lamella or picket and cut it to length.
- Forming + double-line cutting
JCX-fence1 roll forming line for metal fence pickets
The JCX-fence1 roll forms metal pickets for repeat production of Dura-style fencing. Supply the cross-section, strip thickness and coil finish to define the tooling. Specify the end finish and how each picket attaches to the rail. During an acceptance run, compare the first and last pieces for length consistency and twist.
JCX (Golden Integrity)14 000 $ (≈ 12 510 €) · per set - Forming + hydraulic cutting
JCX-Rfence roll forming machine for privacy fence slats
The JCX-Rfence roll forms slats for privacy fencing. The edge folds determine how the slats overlap and engage with the side channel. Provide a panel assembly drawing with installed cover width, strip thickness and slat lengths. Ask for a trial using your prepainted material to inspect the coating after forming and check the end fit.
JCX (Golden Integrity)10 000 $ (≈ 8 936 €) · per set - Two profiles · forming + cutting
JCX-808-1559-SCZLB double-row roll former for metal fence pickets
The JCX-808-1559-SCZLB is a double-row cold roll former for metal fence pickets. Match each tooling row and its strip feed to the intended profile drawing. Supply the coil width, steel thickness and finished picket lengths with the enquiry. Request sample pieces from each row to inspect the section, edge finish and fit with the horizontal rail.
JCX (Golden Integrity)16 910 $ (≈ 15 110 €) · per set - Forming + hydraulic shear
Xianfa XF19 roll former for colour-coated steel fence sheets
The Xianfa XF19 forms prepainted steel strip into profiled fence sheets. Define rib pitch, profile depth and effective cover width after overlap when ordering tooling. Request a trial with the coating and thickness you plan to use. Check the fit along the full seam and inspect the finish at the bends.
Xianfa15 500 $ (≈ 13 850 €) · per set - Forming + automatic cutting
Zhongtuo roll forming machine for metal fence pickets and battens
This Zhongtuo machine forms the individual metal pickets or battens that repeat across a fence panel. The longitudinal folds determine the edge appearance and how the part seats on its support. Use a sample panel or section drawing to specify face width, coated stock and the positions of any required fixing holes.
ZhongtuoPrice on request
Presses and machines for fence tips (3)
Form the pointed tip of pickets and the ends of profiles – cold pressing of tubes or hot forging of solid bars.
- Hot forging of bar ends
Nargesa NF70 Hot Forging Machine for Bar Ends
The NF70 shapes heated bar ends using dies for flat, spear and textured tips. Nargesa lists up to 20 mm for round or square mild-steel bar in its main capacity table. For a batch of fence picket tips, specify the outline, width, thickness and length of the formed zone. The die determines how the tip transitions into the main bar. Show how the picket will join the surrounding panel members. Review several cooled samples. Compare tip symmetry, overall picket height and the transition around the visible part of the pattern.
NargesaPrice on request - Hot forging of scroll ends
Nargesa PC16 Hot Forging Machine for Scroll Ends
The PC16 rolls a snail-shaped end on heated steel. These ends are used in ornamental gate, grille and furniture components. The catalogue lists up to 20 mm for round or square bar and 50 × 10 mm for flat bar. For the rolled end to fit the ornament, specify its outside size, opening and direction relative to the rest of the bar. Show the starting blank and the transition into the curl on the drawing. Place the sample end on the drawing of the complete ornament. Check clearance to the adjacent element and compare the curl across a small batch.
NargesaPrice on request - Arrow ends + cutting · 2 cylinders
AONA Hydraulic Fence Picket Spear Tip Forming Machine
This hydraulic machine forms a spear-shaped end on hollow fence pickets. The listed setup is for 20 × 20 mm tube with a 1.5–2 mm wall and uses a separate hydraulic cylinder for cutting stock to length. Tip symmetry and finished height are visible across an entire fence panel. Provide the desired outline and formed dimensions so the supplier can match the die to the picket. A manual stop sets the blank length, so the sample run should include both cut-off and forming. Check several pickets for overall length, tip shape and edge condition before comparing offers. Confirm which tube sections are covered by the separate cut-off tool.
Aona Machinery7 300 $ (≈ 6 523 €) · delivery not included
Wrought-iron profile machines (3)
Embossing of flat and square bar, twisting, baskets and decorative tube work – for fences, gates and railings.
- Cold embossing · rollers
Nargesa NOA60 Cold Embossing Machine for Metal Sections
The NOA60 rolls a relief pattern into metal using profiled rolls. Nargesa lists capacities up to 60 × 60 mm for square tube and 60 × 10 mm for flat bar. A straightening unit with seven adjustable rollers is included. For railing or fence panels, choose the pattern around the visible face and the joint locations. Specify where the pattern should start and finish relative to the cut and assembly. A trial on the same section shows whether the texture is consistent along the stock. Lay several embossed blanks side by side. Check the pattern repeat, measure straightness and check fit in the frame after the section has passed through the straightener.
NargesaPrice on request - Cold forging · CNC
Nargesa MT500A CNC Cold Twisting and Bending Machine
The MT500A CNC cold-forms steel at separate twisting and bending stations. Nargesa lists capacities of up to 40 mm square solid bar for twisting and up to 25 mm square bar for bending. For an ornamental picket, define the twisted zone and the straight ends that attach to the frame. For a scroll, specify the outer contour and where the tail should finish. The tool sets the form, and the CNC setting lets the operator repeat the movement on the next pieces. Place two samples in the panel jig. Compare twist direction and pitch and check that the straight ends meet the mounting points.
NargesaPrice on request - Cold forging · automatic
Nargesa MT150A Automatic Twisting and Bending Machine
The MT150A forms ornamental bars and curves with interchangeable tooling. Nargesa lists solid square-bar capacity up to 20 mm for twisting and 16 mm for bending. The part programmer stores the movement for repeat pieces. For pickets with a short twisted zone, dimension its start and finish from the cut end. This places the visible pattern at a consistent height in the panel. For hooks, bends and scrolls, confirm the actual tool and the straight length needed for clamping. Place the sample parts against the panel frame. Measure the distance from the end to the start of the pattern and compare twist pitch and direction.
NargesaPrice on request
Machines for forged accessories (1)
Scrolls, leaves, flowers and decorative elements for wrought-iron fences and gates. Accessories can also be bought ready-made.
- Hot forging press · 21 t
Nargesa PV21 21 t Hydraulic Hot Forging Press
The PV21 is a vertical hydraulic hot forging press with 21 t of force, a 296 mm stroke and a 250 × 260 mm usable table. It accepts interchangeable tools selected for the workpiece. In a batch of forged leaves or ornamental ends, stock volume and die closure matter. Show the intended profile and the point where it blends into the bar. Check the tool stack height and the clearance needed to locate the blank. Request several trial pieces from matching blanks. Once cooled, compare relief fill, thickness and the location of the transition against the drawing.
NargesaPrice on request
Lock and handle punching for gates (1)
Rectangular cut-outs for the lock, handle and cylinder in gate leaf profiles. Compare the Spanish and the Chinese options.
- Lock punching · 1 stroke
Nargesa PI85 Hydraulic Lock Punching Press for Metal Gates
The PI85 punches openings for a mortise lock body, cylinder and handle in hollow gate sections. Nargesa lists tooling for several square and rectangular sections, including 50 × 50 mm. The die set depends on the section and whether the wall is 1.5 or 2 mm. For a run of pedestrian gates, alignment between the lock body opening, cylinder and handle spindle governs fit-up. The drawing should also identify the tube face that receives the lock faceplate. Nargesa lists a backset range of 18–37 mm. Supply a tube sample and the actual hardware for a trial. Fit the lock, cylinder and handles to the punched section and check their movement once the assembly is complete.
NargesaPrice on request
Punching of 30×30 tubes (4)
The holes in the rails that the pickets pass through, and fixing holes in fence, railing and gate profiles.
- Ironworker · 40 t · CNC
Nargesa MX340G CNC 40 t Hydraulic Punching and Shearing Machine
The 40 t MX340G CNC punches sheet, tubes and steel sections. With the relevant tooling it can also shear, bend or form a part. It has a 100 mm vertical ram stroke, a 180 mm throat and ESA S820 CNC control. A jobbing shop could configure it for slots in mounting plates, corner notches or tube-end forming. Each operation needs its own tool. The controller's tool library helps when returning to a saved setup for a repeat order. Choose two parts from current production. Give the supplier the material, thickness, opening shape and distance to the edge for each. Request sample parts and time the changeover between tools.
NargesaPrice on request - Ironworker · 70 t
Nargesa MX700 70 t Hydraulic Ironworker with 350 mm Throat
The MX700 combines a nominal 70 t force with a 350 mm throat and a 160 mm ram stroke. Its 600 × 350 mm table provides room for tooling and support under larger parts. Throat depth matters when a hole sits well inside a broad plate or when a section flange must pass beside the punch. Check the part with the die, holder and fixture installed. Usable clearance depends on the complete setup. Provide a section through the least accessible hole and dimension it from the part edge. If the job includes notching or bending, specify the finished geometry for that operation and ask for the corresponding tool.
NargesaPrice on request - CNC · 4 tubes at once
AONA CNC Punching and Cutting Machine for Four 30 × 30 mm Tubes
This fence and gate configuration feeds, punches and cuts four 30 × 30 mm tubes in parallel. The Machory quotation covers stock up to 6 m long with a 1.5–2 mm wall. The benefit is most relevant when repeated fence parts share the same hole pattern and cut length. The control sets the hole positions and cut length. Specify tooling from the part drawing and identify each face that needs punching so the supplier can confirm the proposed setup. Request a trial using four full-length stock tubes. Check the first and last finished parts for overall length, distance from the end to the first hole and consistency across all four tubes. Time the complete run with feeding and cut-off included.
Aona Machinery19 000 $ (≈ 16 978 €) · delivery not included - 3 hydraulic heads · fence tubes
AONA Hydraulic Tube Punching Machine with 3 Heads and 5 Dies
Three hydraulic heads and five dies cover different punching tasks in fence and gate fabrication. The quoted package includes a 7 × 12 mm oblong slot in 30 × 30 mm tube and hole layouts to drawing for 50 × 50 and 60 × 60 mm sections. A shop can use different tooling for fence rails and gate hardware. The length stop provides a repeatable datum from the tube end. For a lock, handle or euro cylinder, send the hardware drawings and mark the orientation of each opening on the tube faces. Evaluate one sample from each die during acceptance. Fit the actual hardware to the sample and verify the hole locations on the wall thickness you intend to run.
Aona Machinery12 750 $ (≈ 11 393 €) · delivery not included
V-notching of profiles (2)
A V-notch in the profile, which is then bent into a corner – for fence, railing and gate frames without cutting into two parts.
- 90° notching · 20–50 t
AONA Hydraulic 90° Tube Notching Machine for Bending
This hydraulic notcher prepares a tube or profile for folding into a 90° corner. AONA describes tooling for different sections, including square and rectangular tubing. The die must match the section size and wall thickness. For frames made in smaller runs, start with the finished corner and overall dimensions. The supplier needs the bend location and the permissible gap when the notch closes. Those details determine whether a proposed die suits the part. Send the section drawing and the finished corner drawing together. On the trial part, inspect the tube around the notch and measure the angle after folding. Confirm tooling separately for each required section.
Aona MachineryPrice on request - 90° V-notching · 6 dies
AONA Hydraulic V-Notching Machine with 6 Dies
This semi-automatic hydraulic machine cuts V-notches for folding 90° corners in gate and railing frames. The Machory package lists six dies for 20 × 20, 30 × 30, 40 × 40, 50 × 50, 60 × 40 and 60 × 60 mm tube with a 1.5–2 mm wall. On a frame folded from one length of tube, the notch positions determine the finished side lengths. For a 60 × 40 mm rectangular section, identify the face that must be visible after folding and show that orientation on the tooling drawing. Assess the test piece after folding. Check the finished angle, edge alignment and frame dimensions. For repeat production, request several consecutive parts positioned using the length stop.
Aona Machinery12 350 $ (≈ 11 036 €) · delivery not included
Fence post lines (8)
Roll forming posts from coil with in-line punching. Alternative: ready-made tube, saw and punching.
- Punching + forming + cutting
Linbay roll forming line for peach or Z mesh fence posts
The Linbay mesh fence line is configured to the selected post section, including peach or Z profiles. Define the open-side width, slot shape and points of contact with the panel. Confirm how the section is closed or secured for your drawing. Fit sample posts to an actual panel and check the top, middle and bottom connections.
LinbayPrice on request - Punching + forming + flying cut
Linbay automatic U-channel post line with 110 t press
The Linbay automatic line combines pre-punching on a 110 t press with roll forming of U-channel posts. Specify the flat blank and where its holes should sit after the channel is formed. In the trial, check the first hole-to-end distance and repeatability on short and long posts. Confirm the included dies and forming rolls.
LinbayPrice on request - Forming + flying cut
Linbay fence post roll forming line with flying cut-off
The Linbay flying cut-off line cuts each fence post as the section travels through the machine. It suits longer repeat runs of a single cross-section. Verify length accuracy at production speed and the position of holes relative to both ends. Plan the support and receiving area for the longest post after cut-off.
LinbayPrice on request - Forming + stop-to-cut
Linbay stop-to-cut fence post roll forming line
On this Linbay line, feed pauses for each cut and the tool stays fixed to the machine. Size the build around the number of posts, the length range and the frequency of order changes. A run of the shortest parts shows how stopping affects real cycle time. Measure finished lengths and inspect section shape at the cut.
LinbayPrice on request - Forming + hydraulic cutting
Yanwu YWpeach-8 automatic peach-profile fence post line
The Yanwu YWpeach-8 automatically forms peach-profile posts for wire mesh fence panels. The slot geometry and pitch need to match the wires that engage with the post. Supply the section, strip thickness, finish and panel connection drawing with the enquiry. Request a sample post and check the fit along the full panel height.
Yanwu40 000 $ (≈ 35 743 €) · per piece - Pre-cut + forming + post-cut
ZLM Liming roll forming line for fence posts and palisade sections
The ZLM Liming line cold forms posts and palisade sections from steel strip. Define the two product types on separate drawings with holes, folds and fixing dimensions. Ask the builder to specify roll sets, cut-off tooling and the changeover steps for each section. Test the samples against the actual brackets and fasteners used in your fence system.
ZLM (Liming)35 000 $ (≈ 31 275 €) · per set, delivery not included - Pre-punch + forming + cutting
ZLM Liming vineyard and fence post roll forming line
ZLM Liming offers a roll forming line for vineyard and fence posts. For trellis posts, define the position of wire slots or holes and which face is exposed. Supply the panel attachment drawing for the fence version. Agree on tooling changeover between sections and inspect trial pieces for length, straightness and hole alignment.
ZLM (Liming)42 000 $ (≈ 37 530 €) · per set, delivery not included - Forming + hydraulic cutting
Zhongtuo roll forming line for steel privacy fence posts and rails
This Zhongtuo configuration makes the structural profiles for steel privacy fencing. The posts locate the ends of each bay, while the rails locate and support the infill. Supply a section drawing for each profile and an assembled panel drawing to define the tooling, fixing features and cut lengths.
ZhongtuoPrice on request
Arch bending for gates and railings (7)
Three-roll machines that bend profiles and tubes into an arc – arched gates, doors and railings.
- Section bender · 3 rollers
Nargesa MC150B Three-Roll Section Bending Machine
The MC150B is a pyramid-type section bender with three rolls. The two lower rolls feed the stock, and the upper roll position governs the curvature. Nargesa lists round tube capacity up to 50 mm outside diameter. The machine suits furniture arches, hoops and individual curved sections. When ordering rolls for rectangular stock, identify the face that will remain on the outside of the bend. Bending on the wide face and the narrow face calls for different tool and support arrangements. Measure chord and rise after the sample is released. Check the section width at the middle of the arc and the remaining straight length at each end.
NargesaPrice on request - Section bender · 3 rollers
Nargesa MC200 Section Roll Bender for Rings and Arcs
The MC200 is a three-roll bender with two driven lower rolls. A millimetre scale records the upper shaft position. Side correctors guide the stock and can help form helical shapes. For a ring or flange, evaluate how the ends meet after rolling. The drawing should specify the diameter, remaining straight portions and joining gap. For a helix, add the axial pitch and handedness. Nargesa describes nine standard rolls with spacers. Request the roll arrangement for your section, then check flatness and how the ends meet on the trial ring.
NargesaPrice on request - Section bender · hydraulic
Nargesa MC200H Hydraulic Section Roll Bender
The MC200H bends sections on three rolls. The two lower rolls are driven and the upper shaft is adjusted hydraulically. The position scale gives the operator a reference when repeating a batch on the same section. A typical job is a matched pair of arches for a double-leaf gate. Section orientation and the visible face matter as much as the radius. The roll set must guide the section consistently, and both arches should match after the load is released. Give the supplier the cross-section, wall thickness, chord and rise. Assess the sample against a template and check for twist and marks on the visible faces.
NargesaPrice on request - Section bender · 3 driven rollers
Nargesa MC400 Section Bending Machine with Three Driven Rolls
The MC400 drives all three rolls. Independent lower-roll adjustment positions the contact points for the required section and curve. Nargesa specifies a roll diameter of 130 mm. For an exposed stainless tube arch, the surface matters alongside the shape. Select rolls for the tube diameter and finish, and identify the face that will remain visible. Measure the cross-section where the curvature puts the most strain on the tube. Ask for a sample on production stock. Compare the curvature, visible roll marks and the straight portions left before trimming.
NargesaPrice on request - Section bender · memory control
Nargesa MC550 Three-Roll Section Bender for Repeat Production
The MC550 uses three driven rolls and a controller that stores their positions for individual curves. This is useful when arches for canopies, supports or railings return as repeat orders on familiar sections. For a series of matching frames, assess how readily the operator restores the settings after changing rolls. Start with consistent blank lengths and identify where the arc must begin. Nargesa offers a separate CNC kit for more complex transitions. Compare the first and last arches after recalling the saved settings. Record the template deviation and confirm the exact controller and rolls on the quotation.
NargesaPrice on request - Section bender · memory control
Nargesa MC650 Section Roll Bender for Long Tubes and Profiles
The MC650 rolls tubes and sections using three driven rolls and asymmetric lower-shaft adjustment. Nargesa lists round tube capacity up to 101.6 mm with the appropriate tooling. Long stock for greenhouses, canopies and frames needs support because its weight affects how it tracks through the rolls. Plan support points and clearance around the machine for the full part envelope. The control stores roll positions for later runs. Trial the longest section in the job. Check access at entry and exit, then measure chord, rise and twist against the drawing tolerances.
NargesaPrice on request - Accessory · measuring
Nargesa Digital Radius Gauge for Bent Tubes and Sections
This digital gauge reads the inside or outside radius of a bent tube or section. Nargesa lists a 55 to 11,250 mm range when the appropriate one of the three standard measuring arcs is fitted. When inspecting a curved frame, choose the surface referenced by the drawing. Inside radius and section centreline radius are different dimensions. On a profile with transitions, take readings within the zones of constant curvature. To assess the gauge, measure a finished arc at several points and compare the readings with a reference template. Confirm the contact base and repeatability required for your parts.
NargesaPrice on request