Fences and gates

Machines for every type of fence: welded 3D panels, roll-formed lamellas, profile fences, wrought iron and gates. Each group shows the finished product first, then the real machines that make it.

Fence from metal profiles

Pickets and rails from square tube, cut, punched, welded and coated.

Cutting profiles to length – Required
Holes and punching – Required
Forming picket tips – Conditional
Decorative elements – Conditional
Positioning and welding – Required
Cleaning and finishing – Required
Powder coating – Conditional
Hot-dip galvanising – External service

Welded 3D panels

Wire is straightened, welded into a mesh panel and bent with V-ribs.

Wire straightening and cutting – Required
Panel welding and V-bending – Required
Posts – Conditional
Powder coating – Conditional
Hot-dip galvanising – External service

Lamella fence

Pre-painted coil is roll formed into lamellas and cut to length.

Roll forming of lamellas – Required
Posts – Conditional
Assembly and packing – Required

Wrought-iron fence

Decorative bars, accessories and arches, welded into panels.

Cutting bars and profiles – Required
Embossing and twisting – Conditional
Forged accessories – Conditional
Tips and ends – Conditional
Arch bending – Conditional
Welding – Required
Powder coating – Conditional
Hot-dip galvanising – External service

Gates

Gate leaves from profiles with lock and handle cut-outs.

Cutting profiles – Required
V-notching for corners – Conditional
Lock and handle cut-outs – Required
Arch bending – Conditional
Welding and fitting – Required
Powder coating – Conditional
Hot-dip galvanising – External service

3D and 2D fence panel lines

Automatic lines that straighten wire, weld the panel and bend the V-ribs of 3D panels. The largest investment in fence production.

Welding + V-bending + stacking
DAPU DP-FP-2500AN automatic 3D fence panel production line
The DAPU DP-FP-2500AN integrates wire feed, welding, servo-controlled bending and stacking for 3D fence panels. Specify the heaviest panel, wire pitches and bend count. At acceptance, follow a full run from wire feed to a finished stack. Verify stack height, bundle outfeed and throughput at your panel geometry.
DAPU
Price on request
Welding · from cut wires
DAPU DP-FP-2500A fence mesh welding machine
The DAPU DP-FP-2500A welds wire mesh for fence panels. DAPU lists a wire diameter range of 3–6 mm. For 3D panels, provide the mesh drawing and bend positions to coordinate welding and downstream bending. During a trial, inspect panel width, mesh pitch and weld quality with the line and cross wire diameters used in production.
DAPU
Price on request
Wire preparation
DAPU GT3-6H CNC wire straightener and cutter for 3–6 mm wire
The DAPU GT3-6H straightens coiled wire and cuts rods for mesh welders. The listed diameter range is 3–6 mm. Specify wire type and the lengths required for line and cross wires. Test straightness and length variation on short and long runs. Match the collection arrangement to the loading method on the welding line.
DAPU
Price on request
Welding + bending + stacking
Sade HLW2500A automatic line for 2D and 3D fence panels
The HLW2500A is the Sade configuration listed for automated production of flat 2D and bent 3D wire mesh fence panels. Specify wire diameters, mesh pitch and the reinforcement bend geometry for each panel. Review the proposed line layout to identify the automated operations and what is involved in changing from one panel type to the other.
Sade (LN)
Price on request
Welding + bending · semi-automatic
Sade HLW2500B semi-automatic 3D fence panel welding and bending line
The HLW2500B combines mesh welding and forming the reinforcement bends in 3D fence panels. To specify the semi-automatic line, define the panel dimensions, wire diameters and number of bends over the panel height. Confirm the operator positions, transfers between stations and discharge of finished panels in the proposed layout.
Sade (LN)
Price on request
Welding + bending + robot stacking
Kaiye KY-RWM-2500 CNC 3D fence panel line with robot stacking
The Kaiye KY-RWM-2500 configuration listed in Machory is intended for series production of welded 3D panels with robot stacking. Specify maximum panel mass, stacking orientation and bundle dimensions along with the mesh pattern. Check the integration of welding, bending and stacking in the quoted line. Request a demonstration with the largest panel and confirmation of the exact configuration code.
Kaiye
68 860 $ (≈ 61 532 €) · per set for 1–2 sets
Welding + bending
Kaiye KY-RWM-2000 welding line for 2 m 3D fence panels
The Kaiye KY-RWM-2000 is a welding line for fence panels with a 2 m working width. For a 3D panel, provide the mesh opening, line and cross wire diameters and positions of the reinforcing bends. Ask for a process layout showing feed, bending and outfeed for the automatic or semi-automatic build. Confirm operator stations and output at your panel size.
Kaiye
62 350 $ (≈ 55 714 €) · per set for 1–2 sets
Mesh welding · modular line
IDEAL Type GA modular mesh welding line
The IDEAL GA family can be configured around a particular product, such as a mesh panel, a flat-bar assembly or a wire cable tray. Feed choices and downstream steps, including trimming or bending where specified, determine the line layout. Provide a finished part drawing with tolerances and the expected production mix to size the equipment.
IDEAL
Price on request
Mesh welding · medium frequency
IDEAL EasyLineWelder 816 wire mesh welding machine
The EasyLineWelder 816 is IDEAL's standardized machine for welded wire mesh products. Submit drawings with panel dimensions and the diameter and spacing of both longitudinal and cross wires. Use those details to check the working field against the product range and confirm the feed arrangement for the intended run.
IDEAL
Price on request

Roll forming lines for lamella fences

Lines that pull sheet from the coil through roller stations, form the lamella or picket and cut it to length.

Forming + double-line cutting
JCX-fence1 roll forming line for metal fence pickets
The JCX-fence1 roll forms metal pickets for repeat production of Dura-style fencing. Supply the cross-section, strip thickness and coil finish to define the tooling. Specify the end finish and how each picket attaches to the rail. During an acceptance run, compare the first and last pieces for length consistency and twist.
JCX (Golden Integrity)
14 000 $ (≈ 12 510 €) · per set
Forming + hydraulic cutting
JCX-Rfence roll forming machine for privacy fence slats
The JCX-Rfence roll forms slats for privacy fencing. The edge folds determine how the slats overlap and engage with the side channel. Provide a panel assembly drawing with installed cover width, strip thickness and slat lengths. Ask for a trial using your prepainted material to inspect the coating after forming and check the end fit.
JCX (Golden Integrity)
10 000 $ (≈ 8 936 €) · per set
Two profiles · forming + cutting
JCX-808-1559-SCZLB double-row roll former for metal fence pickets
The JCX-808-1559-SCZLB is a double-row cold roll former for metal fence pickets. Match each tooling row and its strip feed to the intended profile drawing. Supply the coil width, steel thickness and finished picket lengths with the enquiry. Request sample pieces from each row to inspect the section, edge finish and fit with the horizontal rail.
JCX (Golden Integrity)
16 910 $ (≈ 15 110 €) · per set
Forming + hydraulic shear
Xianfa XF19 roll former for colour-coated steel fence sheets
The Xianfa XF19 forms prepainted steel strip into profiled fence sheets. Define rib pitch, profile depth and effective cover width after overlap when ordering tooling. Request a trial with the coating and thickness you plan to use. Check the fit along the full seam and inspect the finish at the bends.
Xianfa
15 500 $ (≈ 13 850 €) · per set
Forming + automatic cutting
Zhongtuo roll forming machine for metal fence pickets and battens
This Zhongtuo machine forms the individual metal pickets or battens that repeat across a fence panel. The longitudinal folds determine the edge appearance and how the part seats on its support. Use a sample panel or section drawing to specify face width, coated stock and the positions of any required fixing holes.
Zhongtuo
Price on request

Presses and machines for fence tips

Form the pointed tip of pickets and the ends of profiles – cold pressing of tubes or hot forging of solid bars.

Hot forging of bar ends
Nargesa NF70 Hot Forging Machine for Bar Ends
The NF70 shapes heated bar ends using dies for flat, spear and textured tips. Nargesa lists up to 20 mm for round or square mild-steel bar in its main capacity table. For a batch of fence picket tips, specify the outline, width, thickness and length of the formed zone. The die determines how the tip transitions into the main bar. Show how the picket will join the surrounding panel members. Review several cooled samples. Compare tip symmetry, overall picket height and the transition around the visible part of the pattern.
Nargesa
Price on request
Hot forging of scroll ends
Nargesa PC16 Hot Forging Machine for Scroll Ends
The PC16 rolls a snail-shaped end on heated steel. These ends are used in ornamental gate, grille and furniture components. The catalogue lists up to 20 mm for round or square bar and 50 × 10 mm for flat bar. For the rolled end to fit the ornament, specify its outside size, opening and direction relative to the rest of the bar. Show the starting blank and the transition into the curl on the drawing. Place the sample end on the drawing of the complete ornament. Check clearance to the adjacent element and compare the curl across a small batch.
Nargesa
Price on request
Arrow ends + cutting · 2 cylinders
AONA Hydraulic Fence Picket Spear Tip Forming Machine
This hydraulic machine forms a spear-shaped end on hollow fence pickets. The listed setup is for 20 × 20 mm tube with a 1.5–2 mm wall and uses a separate hydraulic cylinder for cutting stock to length. Tip symmetry and finished height are visible across an entire fence panel. Provide the desired outline and formed dimensions so the supplier can match the die to the picket. A manual stop sets the blank length, so the sample run should include both cut-off and forming. Check several pickets for overall length, tip shape and edge condition before comparing offers. Confirm which tube sections are covered by the separate cut-off tool.
Aona Machinery
7 300 $ (≈ 6 523 €) · delivery not included

Wrought-iron profile machines

Embossing of flat and square bar, twisting, baskets and decorative tube work – for fences, gates and railings.

Cold embossing · rollers
Nargesa NOA60 Cold Embossing Machine for Metal Sections
The NOA60 rolls a relief pattern into metal using profiled rolls. Nargesa lists capacities up to 60 × 60 mm for square tube and 60 × 10 mm for flat bar. A straightening unit with seven adjustable rollers is included. For railing or fence panels, choose the pattern around the visible face and the joint locations. Specify where the pattern should start and finish relative to the cut and assembly. A trial on the same section shows whether the texture is consistent along the stock. Lay several embossed blanks side by side. Check the pattern repeat, measure straightness and check fit in the frame after the section has passed through the straightener.
Nargesa
Price on request
Cold forging · CNC
Nargesa MT500A CNC Cold Twisting and Bending Machine
The MT500A CNC cold-forms steel at separate twisting and bending stations. Nargesa lists capacities of up to 40 mm square solid bar for twisting and up to 25 mm square bar for bending. For an ornamental picket, define the twisted zone and the straight ends that attach to the frame. For a scroll, specify the outer contour and where the tail should finish. The tool sets the form, and the CNC setting lets the operator repeat the movement on the next pieces. Place two samples in the panel jig. Compare twist direction and pitch and check that the straight ends meet the mounting points.
Nargesa
Price on request
Cold forging · automatic
Nargesa MT150A Automatic Twisting and Bending Machine
The MT150A forms ornamental bars and curves with interchangeable tooling. Nargesa lists solid square-bar capacity up to 20 mm for twisting and 16 mm for bending. The part programmer stores the movement for repeat pieces. For pickets with a short twisted zone, dimension its start and finish from the cut end. This places the visible pattern at a consistent height in the panel. For hooks, bends and scrolls, confirm the actual tool and the straight length needed for clamping. Place the sample parts against the panel frame. Measure the distance from the end to the start of the pattern and compare twist pitch and direction.
Nargesa
Price on request

Machines for forged accessories

Scrolls, leaves, flowers and decorative elements for wrought-iron fences and gates. Accessories can also be bought ready-made.

Hot forging press · 21 t
Nargesa PV21 21 t Hydraulic Hot Forging Press
The PV21 is a vertical hydraulic hot forging press with 21 t of force, a 296 mm stroke and a 250 × 260 mm usable table. It accepts interchangeable tools selected for the workpiece. In a batch of forged leaves or ornamental ends, stock volume and die closure matter. Show the intended profile and the point where it blends into the bar. Check the tool stack height and the clearance needed to locate the blank. Request several trial pieces from matching blanks. Once cooled, compare relief fill, thickness and the location of the transition against the drawing.
Nargesa
Price on request

Lock and handle punching for gates

Rectangular cut-outs for the lock, handle and cylinder in gate leaf profiles. Compare the Spanish and the Chinese options.

Lock punching · 1 stroke
Nargesa PI85 Hydraulic Lock Punching Press for Metal Gates
The PI85 punches openings for a mortise lock body, cylinder and handle in hollow gate sections. Nargesa lists tooling for several square and rectangular sections, including 50 × 50 mm. The die set depends on the section and whether the wall is 1.5 or 2 mm. For a run of pedestrian gates, alignment between the lock body opening, cylinder and handle spindle governs fit-up. The drawing should also identify the tube face that receives the lock faceplate. Nargesa lists a backset range of 18–37 mm. Supply a tube sample and the actual hardware for a trial. Fit the lock, cylinder and handles to the punched section and check their movement once the assembly is complete.
Nargesa
Price on request

Punching of 30×30 tubes

The holes in the rails that the pickets pass through, and fixing holes in fence, railing and gate profiles.

Ironworker · 40 t · CNC
Nargesa MX340G CNC 40 t Hydraulic Punching and Shearing Machine
The 40 t MX340G CNC punches sheet, tubes and steel sections. With the relevant tooling it can also shear, bend or form a part. It has a 100 mm vertical ram stroke, a 180 mm throat and ESA S820 CNC control. A jobbing shop could configure it for slots in mounting plates, corner notches or tube-end forming. Each operation needs its own tool. The controller's tool library helps when returning to a saved setup for a repeat order. Choose two parts from current production. Give the supplier the material, thickness, opening shape and distance to the edge for each. Request sample parts and time the changeover between tools.
Nargesa
Price on request
Ironworker · 70 t
Nargesa MX700 70 t Hydraulic Ironworker with 350 mm Throat
The MX700 combines a nominal 70 t force with a 350 mm throat and a 160 mm ram stroke. Its 600 × 350 mm table provides room for tooling and support under larger parts. Throat depth matters when a hole sits well inside a broad plate or when a section flange must pass beside the punch. Check the part with the die, holder and fixture installed. Usable clearance depends on the complete setup. Provide a section through the least accessible hole and dimension it from the part edge. If the job includes notching or bending, specify the finished geometry for that operation and ask for the corresponding tool.
Nargesa
Price on request
CNC · 4 tubes at once
AONA CNC Punching and Cutting Machine for Four 30 × 30 mm Tubes
This fence and gate configuration feeds, punches and cuts four 30 × 30 mm tubes in parallel. The Machory quotation covers stock up to 6 m long with a 1.5–2 mm wall. The benefit is most relevant when repeated fence parts share the same hole pattern and cut length. The control sets the hole positions and cut length. Specify tooling from the part drawing and identify each face that needs punching so the supplier can confirm the proposed setup. Request a trial using four full-length stock tubes. Check the first and last finished parts for overall length, distance from the end to the first hole and consistency across all four tubes. Time the complete run with feeding and cut-off included.
Aona Machinery
19 000 $ (≈ 16 978 €) · delivery not included
3 hydraulic heads · fence tubes
AONA Hydraulic Tube Punching Machine with 3 Heads and 5 Dies
Three hydraulic heads and five dies cover different punching tasks in fence and gate fabrication. The quoted package includes a 7 × 12 mm oblong slot in 30 × 30 mm tube and hole layouts to drawing for 50 × 50 and 60 × 60 mm sections. A shop can use different tooling for fence rails and gate hardware. The length stop provides a repeatable datum from the tube end. For a lock, handle or euro cylinder, send the hardware drawings and mark the orientation of each opening on the tube faces. Evaluate one sample from each die during acceptance. Fit the actual hardware to the sample and verify the hole locations on the wall thickness you intend to run.
Aona Machinery
12 750 $ (≈ 11 393 €) · delivery not included

V-notching of profiles

A V-notch in the profile, which is then bent into a corner – for fence, railing and gate frames without cutting into two parts.

90° notching · 20–50 t
AONA Hydraulic 90° Tube Notching Machine for Bending
This hydraulic notcher prepares a tube or profile for folding into a 90° corner. AONA describes tooling for different sections, including square and rectangular tubing. The die must match the section size and wall thickness. For frames made in smaller runs, start with the finished corner and overall dimensions. The supplier needs the bend location and the permissible gap when the notch closes. Those details determine whether a proposed die suits the part. Send the section drawing and the finished corner drawing together. On the trial part, inspect the tube around the notch and measure the angle after folding. Confirm tooling separately for each required section.
Aona Machinery
Price on request
90° V-notching · 6 dies
AONA Hydraulic V-Notching Machine with 6 Dies
This semi-automatic hydraulic machine cuts V-notches for folding 90° corners in gate and railing frames. The Machory package lists six dies for 20 × 20, 30 × 30, 40 × 40, 50 × 50, 60 × 40 and 60 × 60 mm tube with a 1.5–2 mm wall. On a frame folded from one length of tube, the notch positions determine the finished side lengths. For a 60 × 40 mm rectangular section, identify the face that must be visible after folding and show that orientation on the tooling drawing. Assess the test piece after folding. Check the finished angle, edge alignment and frame dimensions. For repeat production, request several consecutive parts positioned using the length stop.
Aona Machinery
12 350 $ (≈ 11 036 €) · delivery not included

Fence post lines

Roll forming posts from coil with in-line punching. Alternative: ready-made tube, saw and punching.

Punching + forming + cutting
Linbay roll forming line for peach or Z mesh fence posts
The Linbay mesh fence line is configured to the selected post section, including peach or Z profiles. Define the open-side width, slot shape and points of contact with the panel. Confirm how the section is closed or secured for your drawing. Fit sample posts to an actual panel and check the top, middle and bottom connections.
Linbay
Price on request
Punching + forming + flying cut
Linbay automatic U-channel post line with 110 t press
The Linbay automatic line combines pre-punching on a 110 t press with roll forming of U-channel posts. Specify the flat blank and where its holes should sit after the channel is formed. In the trial, check the first hole-to-end distance and repeatability on short and long posts. Confirm the included dies and forming rolls.
Linbay
Price on request
Forming + flying cut
Linbay fence post roll forming line with flying cut-off
The Linbay flying cut-off line cuts each fence post as the section travels through the machine. It suits longer repeat runs of a single cross-section. Verify length accuracy at production speed and the position of holes relative to both ends. Plan the support and receiving area for the longest post after cut-off.
Linbay
Price on request
Forming + stop-to-cut
Linbay stop-to-cut fence post roll forming line
On this Linbay line, feed pauses for each cut and the tool stays fixed to the machine. Size the build around the number of posts, the length range and the frequency of order changes. A run of the shortest parts shows how stopping affects real cycle time. Measure finished lengths and inspect section shape at the cut.
Linbay
Price on request
Forming + hydraulic cutting
Yanwu YWpeach-8 automatic peach-profile fence post line
The Yanwu YWpeach-8 automatically forms peach-profile posts for wire mesh fence panels. The slot geometry and pitch need to match the wires that engage with the post. Supply the section, strip thickness, finish and panel connection drawing with the enquiry. Request a sample post and check the fit along the full panel height.
Yanwu
40 000 $ (≈ 35 743 €) · per piece
Pre-cut + forming + post-cut
ZLM Liming roll forming line for fence posts and palisade sections
The ZLM Liming line cold forms posts and palisade sections from steel strip. Define the two product types on separate drawings with holes, folds and fixing dimensions. Ask the builder to specify roll sets, cut-off tooling and the changeover steps for each section. Test the samples against the actual brackets and fasteners used in your fence system.
ZLM (Liming)
35 000 $ (≈ 31 275 €) · per set, delivery not included
Pre-punch + forming + cutting
ZLM Liming vineyard and fence post roll forming line
ZLM Liming offers a roll forming line for vineyard and fence posts. For trellis posts, define the position of wire slots or holes and which face is exposed. Supply the panel attachment drawing for the fence version. Agree on tooling changeover between sections and inspect trial pieces for length, straightness and hole alignment.
ZLM (Liming)
42 000 $ (≈ 37 530 €) · per set, delivery not included
Forming + hydraulic cutting
Zhongtuo roll forming line for steel privacy fence posts and rails
This Zhongtuo configuration makes the structural profiles for steel privacy fencing. The posts locate the ends of each bay, while the rails locate and support the infill. Supply a section drawing for each profile and an assembled panel drawing to define the tooling, fixing features and cut lengths.
Zhongtuo
Price on request

Arch bending for gates and railings

Three-roll machines that bend profiles and tubes into an arc – arched gates, doors and railings.

Section bender · 3 rollers
Nargesa MC150B Three-Roll Section Bending Machine
The MC150B is a pyramid-type section bender with three rolls. The two lower rolls feed the stock, and the upper roll position governs the curvature. Nargesa lists round tube capacity up to 50 mm outside diameter. The machine suits furniture arches, hoops and individual curved sections. When ordering rolls for rectangular stock, identify the face that will remain on the outside of the bend. Bending on the wide face and the narrow face calls for different tool and support arrangements. Measure chord and rise after the sample is released. Check the section width at the middle of the arc and the remaining straight length at each end.
Nargesa
Price on request
Section bender · 3 rollers
Nargesa MC200 Section Roll Bender for Rings and Arcs
The MC200 is a three-roll bender with two driven lower rolls. A millimetre scale records the upper shaft position. Side correctors guide the stock and can help form helical shapes. For a ring or flange, evaluate how the ends meet after rolling. The drawing should specify the diameter, remaining straight portions and joining gap. For a helix, add the axial pitch and handedness. Nargesa describes nine standard rolls with spacers. Request the roll arrangement for your section, then check flatness and how the ends meet on the trial ring.
Nargesa
Price on request
Section bender · hydraulic
Nargesa MC200H Hydraulic Section Roll Bender
The MC200H bends sections on three rolls. The two lower rolls are driven and the upper shaft is adjusted hydraulically. The position scale gives the operator a reference when repeating a batch on the same section. A typical job is a matched pair of arches for a double-leaf gate. Section orientation and the visible face matter as much as the radius. The roll set must guide the section consistently, and both arches should match after the load is released. Give the supplier the cross-section, wall thickness, chord and rise. Assess the sample against a template and check for twist and marks on the visible faces.
Nargesa
Price on request
Section bender · 3 driven rollers
Nargesa MC400 Section Bending Machine with Three Driven Rolls
The MC400 drives all three rolls. Independent lower-roll adjustment positions the contact points for the required section and curve. Nargesa specifies a roll diameter of 130 mm. For an exposed stainless tube arch, the surface matters alongside the shape. Select rolls for the tube diameter and finish, and identify the face that will remain visible. Measure the cross-section where the curvature puts the most strain on the tube. Ask for a sample on production stock. Compare the curvature, visible roll marks and the straight portions left before trimming.
Nargesa
Price on request
Section bender · memory control
Nargesa MC550 Three-Roll Section Bender for Repeat Production
The MC550 uses three driven rolls and a controller that stores their positions for individual curves. This is useful when arches for canopies, supports or railings return as repeat orders on familiar sections. For a series of matching frames, assess how readily the operator restores the settings after changing rolls. Start with consistent blank lengths and identify where the arc must begin. Nargesa offers a separate CNC kit for more complex transitions. Compare the first and last arches after recalling the saved settings. Record the template deviation and confirm the exact controller and rolls on the quotation.
Nargesa
Price on request
Section bender · memory control
Nargesa MC650 Section Roll Bender for Long Tubes and Profiles
The MC650 rolls tubes and sections using three driven rolls and asymmetric lower-shaft adjustment. Nargesa lists round tube capacity up to 101.6 mm with the appropriate tooling. Long stock for greenhouses, canopies and frames needs support because its weight affects how it tracks through the rolls. Plan support points and clearance around the machine for the full part envelope. The control stores roll positions for later runs. Trial the longest section in the job. Check access at entry and exit, then measure chord, rise and twist against the drawing tolerances.
Nargesa
Price on request
Accessory · measuring
Nargesa Digital Radius Gauge for Bent Tubes and Sections
This digital gauge reads the inside or outside radius of a bent tube or section. Nargesa lists a 55 to 11,250 mm range when the appropriate one of the three standard measuring arcs is fitted. When inspecting a curved frame, choose the surface referenced by the drawing. Inside radius and section centreline radius are different dimensions. On a profile with transitions, take readings within the zones of constant curvature. To assess the gauge, measure a finished arc at several points and compare the readings with a reference template. Confirm the contact base and repeatability required for your parts.
Nargesa
Price on request

Pipe cutting machines

Saw, angle and roll cutting machines for tubes – automatic feeding, cut to length, burr-free edge.

Roll cutting · 6 m
AONA Automatic Pipe Roll Cutter with Hydraulic Feeding
This roll cutting machine cuts pipe to length with automatic hydraulic feeding. AONA lists a length of up to 6 m. Ask the supplier to specify the maximum incoming stock length and maximum finished part length separately. For batches of duct parts, metal furniture or tubular assemblies, evaluate the full incoming stock length. Consecutive cuts need to stay within the length tolerance as the feed approaches the end of the pipe. Give the supplier the incoming and finished lengths and the expected lot size. Ask for a trial on one full stock length, the number of accepted pieces and the size of the end remnant. Confirm how finished pieces transfer to the next operation.
Aona Machinery
Price on request
Cold roll cutting · Ø8–260 mm
AONA Automatic Roll Cutter for Round Tubes Ø8–260 mm
This version uses a rotating roller tool for cold cutting round tubes. AONA lists an Ø8–260 mm range. Wall capacity and the setup depend on the diameter, material and configuration. For short sleeves and spacers, both overall length and the usable bore after cutting matter. Compare samples at the smallest and largest sizes in your job using the actual steel grade and wall thickness. Measure several parts for length, ovality and the condition of the inside edge. Request a feed-to-discharge cycle time for each representative size.
Aona Machinery
Price on request
Rotary cold cutting · 6 m
AONA Automatic Rotary Cold Cutting Machine for Pipe
This machine uses a cutting wheel for rotary cold cutting of pipe. AONA describes versions for steel, stainless steel and other materials, with suitability confirmed for the specific pipe. For a pipe that will receive a coupling or undergo further forming, the inside edge affects fit-up. On galvanised stock, include any coating requirements near the cut. Match the wheel to the material and wall thickness. Ask for a cut made on your actual pipe. Measure the bore around the cut and check the fit of the mating component before selecting the setup.
Aona Machinery
Price on request
Saw cutting · roller feed · 6 m
AONA Automatic Tube Saw with Roller Feed
Rollers position the tube for a programmed cut on the circular saw. The Machory configuration lists sections up to 100 × 100 mm with walls up to 2 mm and incoming stock up to 6 m long. This is a candidate for batches of straight blanks for panels, frames and stands. Compare the number of usable pieces produced from a full stock length. Account for saw kerf, any initial end trim and the remnant left by the feed system. Have the supplier cut the shortest and longest parts in your usual mix. Measure several consecutive pieces and check end squareness and edge condition on your actual material.
Aona Machinery
7 900 $ (≈ 7 059 €) · delivery not included
Angle saw · 0–180°
AONA Semi-Automatic Mitre Saw for Tubes and Profiles
This semi-automatic circular saw makes mitre cuts on metal tubes and profiles. In the quoted setup a pneumatic cylinder clamps the part, then the saw feeds, cuts and retracts. The listed sections run from 10 × 10 to 100 × 100 mm with 1.5–2 mm walls. A typical job is cutting left- and right-hand mitres for a frame. Confirm the usable section size at the angle you need, since the cutting geometry changes with the angle and the orientation of the stock. Ask for a pair of matching cuts in your own section. Bring the ends together and check the joint gap, included angle and edge condition before welding.
Aona Machinery
6 500 $ (≈ 5 808 €) · delivery not included

Laser welding machines

Handheld fiber laser welders for steel, stainless and aluminium – many also clean and cut. Compare power, cooling and the functions in one device.

Single-module · water-cooled
Weni WS-EWL single-module fiber laser welder
The Weni WS-EWL is a single-module fiber laser welder with a handheld, water-cooled setup. Its control panel provides access to beam settings for work such as edge seams and joints on thin-wall metal parts. For repeat production, trial butt, fillet and lap joints at your actual thicknesses. Determine when filler wire is needed and check the finished seam against your tolerance. Confirm the welding head, source and cooling unit for the version quoted.
Weni Solution
from 11 000 € (≈ 12 310 $) · net, base configuration
5 in 1 · water-cooled
Weni WS-CWM 5in1 handheld fiber laser welder
The Weni WS-CWM 5in1 is a liquid-cooled handheld fiber laser system. Its modes cover welding, spot tacking, weld cleaning, surface cleaning and thin-metal cutting. The range includes source powers from 1 to 3 kW, depending on configuration. For frames and thin-wall profiles, request a trial using your actual joint gap and fixtures. Assess bead appearance, distortion and filler wire requirements. Specify the chiller, wire feeder and nozzles required for the modes you intend to use.
Weni Solution
from 9 162 € (≈ 10 253 $) · net, base configuration
4 in 1 · air-cooled
Weni WS-HWM-A air-cooled 4-in-1 laser welder
The Weni WS-HWM-A is an air-cooled handheld welder in 1.5 kW V15 and 2 kW V20 versions. Alongside welding, it offers weld cleaning, cutting and spot tacking. The layout suits evaluation for stations where space for equipment is limited. Use a thin stainless sample to check seam consistency and distortion. For long seams, confirm the continuous duty rating under your shop conditions. Check how the handpiece and fiber reach around the assembled part.
Weni Solution
from 6 537 € (≈ 7 316 $) · net, base configuration
4 in 1 · compact
Weni WS-T700 700 W handheld laser welder
The Weni WS-T700 is a compact 700 W handheld laser welder with air cooling. It is intended for work on thin metal parts and includes weld cleaning, cutting and an adjustable interval for spot tacking. For covers and small housings, check joint fit, tack consistency and marks on the visible face. Use your own sheet in the trial to choose the mode. Confirm the kit contents and the nozzles required for the operations you run most often.
Weni Solution
from 5 907 € (≈ 6 611 $) · net, base configuration
Handheld · weld, clean, cut
Mekotek FLW 1 kW handheld fiber laser welder
The Mekotek FLW 1 kW is a handheld fiber laser welder for thin-wall parts. It also offers cleaning and light cutting modes. Evaluate it for covers, signs and small assemblies where the seam is visible. Check how your actual joint gap affects the result. On cover samples, measure flatness after cooling and inspect the exposed face. Confirm wire feed, nozzles and the equipment required at the workstation.
Mekotek Laser
Price on request
Handheld · weld, clean, cut
Mekotek FLW 1.5 kW handheld fiber laser welder
The Mekotek FLW 1.5 kW handheld laser welder also offers cleaning and light cutting. For stainless enclosures and cladding, evaluate it on the fillet and lap joints used throughout a production batch. Prepare samples with two joint geometries. Compare penetration and any finishing needed on the visible seam. Check wire feeding and cooling and ask for the trial settings to be included with the quotation.
Mekotek Laser
Price on request
Handheld · weld, clean, cut
Mekotek FLW 2 kW handheld laser welding system
The Mekotek FLW 2 kW is a handheld fiber laser welding system with cleaning and light cutting modes. For batches of frames or housings with long seams, trial it on your most demanding joint. Inspect seam consistency along its full length and part geometry after cooling. Confirm cooling and duty rating for repeated cycles. Request an itemised list of nozzles and accessories for the planned operations.
Mekotek Laser
Price on request
Handheld · weld, cut, clean
Nargesa MS20 2 kW Handheld Laser Welding Machine
The MS20 is a handheld machine rated at 2 kW laser output. Nargesa lists welding, cutting and cleaning modes. Select the welding configuration for the joint and the requirement for filler wire. For a visible stainless assembly, specify the joint type, thicknesses and acceptable gap between the edges. Use the production fixture during the trial. Assess bead appearance and penetration as separate acceptance criteria. Request a welded sample and a cross-section of the weld to the drawing requirements. Check distortion after cooling and include integration with the planned laser booth in the quotation.
Nargesa
Price on request
Safety booth · modular
Nargesa CSL Modular Laser Welding Safety Booth
The CSL is a modular enclosure for Class 4 laser work areas. Nargesa describes a protective window, a monitoring camera and interlocked double doors. In an MS20 installation, opening the door interrupts the laser enable signal. Size the layout around the table, workpieces and loading route. The position of the panels and doors needs to allow access for the largest part and for servicing. Nargesa provides a prior integration assessment for lasers from other manufacturers. Provide the room plan, laser model and work area dimensions for a quote. Request a booth drawing, an interlock description and the specified provisions for fume extraction.
Nargesa
Price on request
4-in-1 · 1.5 kW
Aktona TR-W1500 1.5 kW handheld laser welder
The Aktona TR-W1500 is a 1.5 kW handheld fiber laser system with welding, cutting, surface cleaning and weld-cleaning modes. It is worth evaluating for thin covers and housings where marks on the visible face matter. Provide a sample with your actual joint gap and fixtures. Compare seam appearance, distortion and the need for filler wire. Ask which equipment is supplied for the four modes and what is required to set up the workstation.
Aktona
from 6 534 € (≈ 7 312 $) · net, base configuration
4-in-1 · 2 kW
Aktona TR-W2000 2 kW handheld fiber laser welder
The Aktona TR-W2000 is a 2 kW handheld laser welder with cutting and cleaning modes. For repeat frame or corner assemblies, compare the complete cycle from fixturing to the finished seam. On a thin-wall profile trial, check dimensions after cooling and the appearance of the outer corner. If filler is planned, specify the wire feeder and rollers. Confirm which welding head and source are included in the exact version quoted.
Aktona
from 7 890 € (≈ 8 830 $) · net, base configuration
4-in-1 · 3 kW
Aktona TR-W3000 3 kW handheld laser welder
The Aktona TR-W3000 is a 3 kW handheld fiber laser with four modes, including welding, cutting and cleaning. Evaluate this version on your most demanding joints, such as assemblies with different wall thicknesses. For a sample run, specify required penetration, seam length and distortion limits. Confirm the cooling package and duty cycle for extended seams. Check the quotation against the exact 4-in-1 kit, including its head and accessories.
Aktona
from 9 020 € (≈ 10 094 $) · net, base configuration

Robotic welding cells

Welding robots with rotary tables, positioners and tracks – repeatable MIG/MAG welds on frames, structures and series parts.

Robot cell · rotary table Ø800 · 500 kg
Aktona robotic MIG/MAG welding cell with rotary table
The Aktona cell pairs a six-axis MIG/MAG robot with a rotary table. The positioner turns the assembly to bring seams into the torch's working range. It is worth evaluating for repeat frames and mounting assemblies. Include the part and fixture weight and envelope in the specification. Time the complete cycle with loading, repositioning and unloading. Confirm the workholding, guarding and acceptance trials covered by the quotation.
Aktona
from 22 495 € (≈ 25 174 $) · net, base configuration
Robot cell · 4 m track · 1000 kg positioner
Aktona robotic MIG/MAG welding cell with track and positioner
The Aktona MIG/MAG cell combines a track-mounted six-axis robot with a headstock and tailstock positioner. Linear travel lets the torch follow seams on long fabrications, while rotation provides access at different weld positions. Check end seams, areas behind stiffeners and space for fixture attachment. Include tacking and repositioning in the cycle. Confirm actual travel, load capacity and the cell guarding covered by the project.
Aktona
from 33 798 € (≈ 37 823 $) · net, base configuration

Deburring and grinding machines

Belt, brush and polishing machines that remove burrs and oxide and round the edges of parts after laser, plasma and punching.

Deburring · 1000 mm · 2 belts + polisher
Aktona RRP1000 deburring machine with linear polishing
The Aktona RRP1000 processes flat parts across a 1000 mm working width. Two abrasive belt modules remove burrs left by laser cutting, punching or plasma cutting. A linear polishing module addresses the appearance of the exposed face. Vacuum and magnetic tables suit different small-part holding conditions. Test your shortest part and a panel where the finish direction is visible. Check whether the linear module is included in the quoted configuration and which abrasives it uses.
Aktona
from 10 603 € (≈ 11 866 $) · net, base configuration
Deburring · 1300 mm · 2 belts + flap brushes
Aktona RRW1300 deburring and edge rounding machine
The Aktona RRW1300 is a through-feed deburring machine with a 1300 mm working width. Two belt modules take off burrs, and a flap brush module works the edge. The sequence fits parts that go on to coating or assembly. On perforated panels, inspect both the inner contours and the outside perimeter. Select vacuum or magnetic hold-down for the material and part size. If a specific edge radius is required, measure it on a sample and check how the result holds after an abrasive change.
Aktona
from 21 455 € (≈ 24 010 $) · net, base configuration

Laser cleaning machines

Remove rust, paint, oil and oxides without sandblasting or chemicals. Continuous lasers for heavy cleaning, pulse lasers for delicate surfaces.

Continuous · water-cooled
Weni WS CLM PRO water-cooled fiber laser cleaner
Weni WS CLM PRO is a water-cooled fiber laser cleaning range. Its 1 to 3 kW versions suit applications such as removing rust and old coatings from steel parts before further processing. Use a representative sample to select power and scan width. For large assemblies, check fiber reach and access to recessed surfaces. Compare the area cleaned per hour, the finish left on the base metal and the extraction required for the specific coating.
Weni Solution
from 7 325 € (≈ 8 197 $) · net, base configuration
Continuous · air-cooled
Weni WS CLM-A air-cooled fiber laser cleaner
Weni WS CLM-A is an air-cooled fiber laser cleaner for removing rust, paint and contamination from metal surfaces. The 1.5 and 2 kW versions have a compact layout for shops that move cleaning work between stations. Check whether the fiber and handpiece reach around welds and ribs. For longer cleaning runs, confirm the duty cycle at your shop temperature. Compare the two power levels by timing removal of the same coating over an equal area.
Weni Solution
from 7 918 € (≈ 8 861 $) · net, base configuration
Pulsed · delicate surfaces
Weni WS-CLM-Pulse pulsed fiber laser cleaner
The Weni WS-CLM-Pulse uses a pulsed fiber source for local removal of deposits, oxides and coatings. It is worth trialling on tooling or precision parts where the condition of the underlying surface matters after cleaning. Provide the substrate and the type and thickness of the layer to be removed. Assess how pulse energy, lens choice and scan area affect the result. Compare cleanliness and any visible changes to the substrate before selecting the source.
Weni Solution
from 14 570 € (≈ 16 305 $) · net, base configuration

Complete lines and pretreatment

Manual and automatic powder coating lines, washing and phosphating before coating, cyclones, powder centres and reciprocators.

Manual set · booth S-1115 + 6.5 kW oven + gun
COLO powder coating starter set with booth, oven and gun
The COLO starter set brings together a spray booth, a powder gun and a curing oven for manual small-batch work. It fits a shop finishing brackets, plates or compact housings. Measure the largest part on its fixture and check that it passes through both the booth opening and the oven door. Ask for the three model codes, the electrical connection requirements and the supplied powder-feed equipment to compare package quotations.
COLO
6 430 $ (≈ 5 746 €) · per set, delivery not included
Manual line · 7 m booth + 7 m gas oven
COLO manual powder coating line for fence panels
This manual COLO line is configured for fence panels, gates and similar long fabrications. Hanging slatted or tubular panels should leave both faces and welded joints accessible. Base oven length and booth approach on the longest panel together with its carrier. Include panels per batch, entrance dimensions and the planned turning or transfer arrangement in the enquiry so the proposed layout matches the workpieces.
COLO
Price on request
Manual line · booth + 5 m gas / diesel oven
COLO manual batch powder coating line for steel frames
This COLO manual line arranges application and curing around batches of fabricated steel frames. It fits a shop handling several frame sizes and changing order quantities. Determine how many frames a carrier can hold while leaving the inside corners accessible. Allow a staging area between the booth and oven, and confirm the batch loading arrangement and any pretreatment equipment included in the quotation.
COLO
Price on request
Manual line · walk-in booth + gas oven · top track
COLO manual powder coating line with overhead track
This manual COLO line moves suspended parts along an overhead track between workstations. It suits frames and welded assemblies that are coated and cured in a hanging position. Provide the combined mass of each part and carrier and the required clearance below the track. Check the oven transfer, staging locations and how carriers accumulate or pass one another in the proposed layout.
COLO
Price on request
Automatic cyclone booth + reciprocator + batch oven
COLO semi-automatic powder coating line for steel plates
The COLO semi-automatic steel plate line combines automatic application with a manually loaded batch oven. Consistent plate geometry makes it possible to plan the gun positions around a recurring workpiece envelope. Decide how edges will be covered and how operators will move coated plates to curing. Provide maximum size and weight, the required face coverage and expected plates per shift to size the line.
COLO
Price on request
Powder feed · ultrasonic sieve · PLC
Vogamakina VM powder centre for automatic coating lines
The Vogamakina VM powder centre manages supply to the guns on an automatic line. In a configured recovery system, transfer equipment brings fresh powder and cyclone reclaim into the feed. Match this station to the booth, sieve and control system. Specify how many guns run at once, how the powder mix is monitored and what is cleaned between colours. Check the supplied pumps, hoses and interfaces against the line layout.
Vogamakina
Price on request
Gun mover · 7" touch · 10 programs
Vogamakina VM vertical reciprocator for automatic powder guns
The Vogamakina VM vertical reciprocator moves automatic powder guns up and down as parts travel through the booth. Stroke and speed are set around part height and line operation. Provide the gun count, total mounting load and useful stroke for sizing. Check hose routing, maintenance access and how the gun motion is coordinated with the conveyor speed in the planned line.
Vogamakina
Price on request
Pretreatment · 2–3 stages · AISI 304
Vogamakina manual spray cabinet for chemical pretreatment
The Vogamakina manual cabinet gives operators a spray station for preparing metal parts before coating. The manufacturer describes an AISI 304 stainless build and two- or three-stage configurations according to the process. Supply the largest part dimensions, substrate, incoming surface condition and rinse requirements. Check how process liquids are collected, how all faces are reached and which utility connections the installation needs.
Vogamakina
Price on request
Spray tunnel · stages to the process
Vogamakina automatic tunnel line for surface pretreatment
The Vogamakina automatic pretreatment tunnel prepares suspended parts before coating. Separate zones are sized around the material and process, such as washing, degreasing and rinsing. For continuous production, zone length and conveyor speed are designed together. Provide the maximum part envelope, substrates, target throughput and site conditions for water and effluent handling. Check which tanks, pumps and controls the quotation includes.
Vogamakina
Price on request
Automatic line · 1–6 m/min · 500–5000 parts/h
Elektrosprey tunnel-type electrostatic powder coating line
The Elektrosprey tunnel line moves workpieces through consecutive stations on a conveyor. Throughput depends on speed, hanger pitch and the time required in each zone. State the substrates, part masses and target pieces per shift. Check pretreatment stages, booth scope and heated oven length against the heaviest product in the mix.
Elektrosprey
Price on request
Pretreatment · 5–9 dip stages
Elektrosprey dip-type metal surface pretreatment line
The Elektrosprey dip line prepares metal surfaces through a sequence of baths before coating. Select the stages around the substrate, incoming contamination and coating requirements. Provide the largest loaded carrier and batches per shift for sizing. Check tank dimensions, transfer, drainage between stages and the site water and effluent connections.
Elektrosprey
Price on request
Cyclone · 10 000–20 000 m³/h
ROMER CK-D low-profile powder recovery cyclone
The ROMER CK-D range separates powder from booth extraction air where available height is limited. A stainless steel hopper, screen and vibrator collect and screen recovered material. An RP-01 connection lets the recovery circuit transfer it back to the powder feed system. For a retrofit, measure overhead clearance and match cyclone airflow and pressure drop to the extraction fan. Where powder is reused, agree on how the hopper, screen and transfer route will be cleaned between colours.
ROMER
Price on request
Turnkey line · washer, dryer, booth, gas oven, 120 m conveyor
ROMER automatic powder coating line
A ROMER automatic powder coating line combines tunnel washing, drying, powder application and curing on an overhead conveyor. In repeat production, the line gives each metal part the same sequence of process stages. Size the line from the part and hanger envelope, target hangers per hour and required surface treatment. Specify the largest frame or panel before selecting conveyor and booth dimensions. At acceptance, check pretreatment results and log the curing temperature on a representative part.
ROMER
Price on request
Pretreatment · manual pressure washing · 11 kW
ROMER MS Pressure Washing Booth for Surface Preparation
The ROMER MS is a stationary pressure washing booth for pretreatment. ROMER offers two- or three-stage arrangements that can include degreasing and phosphating according to the process. For welded frames, identify the contamination to remove and the points that can trap solution. Part position affects access to corners and how it drains after rinsing. Supply the part envelope and typical contamination. Ask for the process stages, solution return arrangement and the water quality specified for the final rinse.
ROMER
Price on request
Automatic corona gun for lines and robots
Gema OptiGun GA04 automatic powder coating gun OptiGun® GA04
The Gema OptiGun GA04 is an automatic powder gun for integration into a booth. Define the target faces, part motion and mounting position before selecting the build. Match nozzle and powder feed to the controller and the planned distance from the part. Ask for a trial on a representative workpiece to assess face, edge and recess coverage.
Gema
Price on request
Gun control unit for automatic lines
Gema OptiStar 4.0 CG20 automatic powder gun controller OptiStar® 4.0 CG20
The Gema OptiStar 4.0 CG20 controls pneumatic and electrostatic parameters for an automatic powder gun. For a retrofit, identify the gun, powder feed and how the central line control selects recipes. Check supplied cables and the cabinet interfaces. Trial two repeat products to confirm that settings can be recalled when production changes over.
Gema
Price on request
Automatic corona gun for coating lines
Wagner PEA-X1 automatic corona powder coating gun
The Wagner PEA-X1 is an automatic corona-charging gun for integration into a powder coating line. Its modular design can be configured with nozzles and accessories for the application. Specify the mount, part geometry and areas to sample. Confirm compatibility with the controller, powder feed and moving or fixed gun support. Ask for a list of nozzles and wear parts for the exact line configuration.
Wagner
Price on request
Automated powder management centre for auto lines
ROMER ProfiCenter CP02 powder feed centre
ROMER ProfiCenter CP02 manages powder feed for an automatic coating booth. Its sealed fluidised hopper takes fresh powder from a box. Depending on the selected mode, recovered powder is mixed back into the feed or routed to waste. Compressed-air cleaning and Modbus communication support integration with the line. For a retrofit, check RP-01 connections, control signals and hose access. If colour carryover is critical, use a dark-to-light changeover trial to assess the cleaning procedure.
ROMER
Price on request
Automatic closed-chamber pretreatment
ROMER Automatic Chamber Washer for Metal Pretreatment
The ROMER chamber washer treats batches using programmed degreasing, rinsing and phosphating stages for the selected process. Its PLC can set treatment times and temperatures. For a batch of brackets, hanger spacing determines whether nozzles reach the inner faces. Give the supplier a section drawing, the intended loading density and the allowed time to drying. Compare parts from the middle and ends of the trial load. Confirm the number of tanks, solution separation and how the solutions are maintained.
ROMER
Price on request
Vertical U-type line for long aluminium profiles
Elektrosprey U-type powder coating line for aluminium profiles
The Elektrosprey U-type line coats aluminium profiles on a route that returns towards the handling area. Size the layout around suspended profile length and separation between carriers on curves. Provide the building layout, maximum part envelope and throughput target. Check loading and unloading positions and the quoted booth, oven and powder feed scope.
Elektrosprey
Price on request
I-beam overhead chain conveyor for paint lines
Vogamakina Webb-type monorail conveyor for coating lines
The Vogamakina Webb-type conveyor carries suspended parts on trolleys driven by a chain along a single rail. The route can be designed with horizontal curves and changes in elevation. Provide loaded hanger mass, carrier spacing and the throughput target for sizing. Check the load rating of the specified chain and the route interfaces at the booth, oven and loading station.
Vogamakina
Price on request
Compact booth + oven set for tyre workshops
Vogamakina powder coating line for car rims
The Vogamakina wheel rim line combines manual booth application with batch curing of a complete set. In the manufacturer's example, the oven takes four 24-inch rims. Rotating hangers give access to spokes and inner rims during application. Specify rim diameter and width, sets per shift and preferred heating source. Agree on how surface preparation will be handled and which stations the quoted package covers.
Vogamakina
Price on request
Automatic gun + control for serial production
COLO-800DA automatic powder application unit
The COLO-800DA controls automatic powder application within a metal finishing line. It suits repeated runs of profiles, panels and frames that pass the guns in a consistent orientation. Map the faces to coat on each pass before integrating the unit with the booth and conveyor. Request a quote detailing gun count, powder feed, individual controls and the interface to part movement. Identify recessed areas that will receive manual touch-up.
COLO
from 700 $ (≈ 626 €) · per piece, MOQ 1

Powder coating booths

Manual booths with cartridge filters, open spray walls, walk-in booths and automatic booths with cyclone recovery – they keep the workshop clean and return the overspray for reuse.

Manual booth · 2 cartridges · 1.5 kW
COLO-S-1115 compact manual powder coating booth
The COLO-S-1115 is a compact manual booth for brackets, plates and small enclosures. The operator works through the front opening while the filter section collects powder carried past the workpiece. Measure the part with its hook attached and allow space to turn it when several faces need coating. Ask for the usable opening, filter type and count, and the clearance needed to replace the cartridges at the planned installation point.
COLO
2 500 $ (≈ 2 234 €) · per unit, delivery not included
Manual booth · 3 cartridges · 4000 m³/h
COLO-1517 manual powder booth with cartridge recovery
The COLO-1517 collects powder through filter cartridges during manual batch coating. It suits parts that an operator can position and coat through the front opening. For single-colour runs, establish how the collected powder is removed and when it can be returned to production. Compare cartridge dimensions, the cleaning arrangement and the service clearance at the rear or side of the proposed booth.
COLO
Price on request
Open booth · 4 cartridges · pulse-jet
COLO-S-3222 open-face powder coating booth
The COLO-S-3222 gives operators a wide front approach to panels, doors and frames during manual application. Choose the part orientation around the faces that must be reached and the position of the filter bank. Tall panels also need space to manoeuvre the hanger in front of the booth. COLO shows several builds in this family. Request a drawing with the clear opening, filter arrangement and required maintenance space.
COLO
Price on request
Walk-in booth · 5 cartridges · 6600 m³/h
COLO-S-3217 walk-in powder booth for heavy parts
The COLO-S-3217 provides walk-in access for manual coating of heavy metal parts. Size the opening around the workpiece and its handling fixture, then check the load capacity along the route to the spray position. Position welded frames so their sides and joints can be reached. Supply a drawing, maximum loaded mass and intended handling method, such as a trolley or suspended carrier, with the project enquiry.
COLO
Price on request
Walk-in booth · 6 cartridges · 8000 m³/h
COLO-3924 large walk-in powder coating booth
The COLO-3924 is a large walk-in booth that gives the operator access around bulky frames, fabrications and long parts. Plan the full route from pretreatment to the curing oven. Include the trolley or hanger when measuring the entrance and leave space to work around the part. Request a layout drawing showing the usable booth envelope, the filter module and the maintenance zones.
COLO
Price on request
Automatic booth · PVC · stainless cyclone
COLO-S-PP automatic plastic powder booth with cyclone
The COLO-S-PP is a plastic booth for an automatic line that changes between colours. Cyclone separation works with the powder supply and automatic guns configured for the project. Describe the colour sequence, expected changeovers per shift and longest production run. Ask to see the wall and powder-path cleaning sequence using your powders. Confirm whether the quotation includes a powder centre, gun reciprocators and the final filtration stage.
COLO
Price on request
Manual booth · one-side open · pulse-jet
Vogamakina VFKW-3 powder coating booth with cartridge filters
The Vogamakina VFKW-3 is a cartridge filter booth for batches of metal parts. The filters collect powder drawn from the working area by the extraction air. Assess the working opening with a typical workpiece on its hanger and check access to every face to be coated. Request the exact VFKW-3 configuration, replacement cartridge size and details of the cleaning and powder collection arrangements.
Vogamakina
6 100 € (≈ 6 827 $) · net, delivery not included
Cyclone + after-filter · steel or PVC
Vogamakina cyclone recovery powder coating booth
Vogamakina's modular cyclone booth uses a cyclone followed by a final filter. Powder separated by the cyclone can be sieved and returned to the feed, while finer particles reach the downstream filter. This arrangement suits lines running consecutive batches with planned powder reuse. Specify the booth opening, cyclone service access and the cleaning sequence between strongly contrasting colours when requesting a quote.
Vogamakina
Price on request
Cartridge booth · 2–12 guns · CE / ATEX
Elektrosprey electrostatic powder coating booth with cartridge filters
The Elektrosprey powder booth uses filter cartridges to collect overspray. Select the build around the clear opening and the way parts are hung and turned. State operator count and the colours used in a typical shift. Check cartridge cleaning, collected powder handling and the space needed for maintenance.
Elektrosprey
Price on request
Manual booth · 2 windows · up to 800 g/min
ROMER KPD manual powder coating booth
The ROMER KPD range is designed for manual powder coating. Versions with two working openings and a door let the operator approach a suspended part from different sides, which helps when coating frames and welded assemblies with recessed corners. Compare the opening dimensions with your part and its hanger. Check the clearance needed to rotate the workpiece and the space required to service the polyester filters. Specify extraction airflow and access layout for the selected booth.
ROMER
Price on request
Enclosed booth · from 0.69 kW · 400 g/min
ROMER KPZ enclosed powder coating booth
ROMER KPZ is an enclosed powder booth range for manual coating. On a batch line, booth size affects the space available to hang the workpiece, reach each surface with the gun and transfer the part to curing. Choose a compact or wider version based on the clear opening and loading route. The booths feature automatic filter cleaning. Include the largest part dimensions with its hooks, the handling method and the expected frequency of colour changes in an enquiry.
ROMER
Price on request
Manual booth · door · 2.2 kW
ROMER KPP Powder Coating Booth with Access Door
The KPP is a manual powder coating booth with one operator opening and an access door. The KPP-2 and KPP-3 differ in opening width and filter area, at 30 and 45 m² respectively. For frames and parts with multiple edges, consider how the operator reaches both faces. The opening governs gun access, while the door affects how the hanging fixture is loaded. Trial the booth with the intended powder and a representative part. Check airflow across the working opening and confirm how the automatic filter-cleaning cycle is configured.
ROMER
from 4 200 € (≈ 4 700 $) · net
Open booth · up to 4 m window
ROMER KPO Open Powder Coating Booth for Panels
The KPO is an open booth with a wide operator opening. The range offers different opening widths, automatic filter cleaning and optional powder recovery. For a fence panel or gate leaf, use the dimensions in its coating position. Show the hanging height and the clearance required for turning. Check gun access to the ends and the back face of the section. Request a booth layout showing your workpiece. On a trial, assess access and powder containment across the full opening at the intended application rate.
ROMER
Price on request
Automatic booth · dielectric · cyclone · ATEX zone 22
ROMER KAP1 automatic powder coating booth
ROMER KAP1 is a dielectric booth for automatic powder application on a conveyor. Part detection works with reciprocators and ProfiSpray A guns so the spray setup can follow the workpiece geometry and how it is hung. Send the minimum and maximum part heights, hanger spacing and any recessed surfaces that need coating. These inputs help specify gun count, reciprocator travel and conveyor speed. For frequent colour changes, include powder recovery and the cleanout sequence in the quotation.
ROMER
Price on request
Manual booth · ClassicStandard / ClassicOpen · 4000–6600 Nm³/h
Gema ClassicLine manual powder coating booths
ClassicLine is Gema's family of manual powder booths for individual workpieces and batches. Select the build around the loaded hanger envelope and access to the different faces of the part. Describe the spray position, number of operators and colour-change routine in the enquiry. Check the clear opening, filter layout and service space on the installation drawing.
Gema
Price on request
Manual booth · 2 cartridges · 3 kW · CE / ATEX
Wagner BASIC 4000 manual suspension powder coating booth
The Wagner BASIC 4000 is a manual booth for individual parts and small batches. Its integrated rotating hook lets the operator reach several faces of a suspended part from the work position. Wagner lists two filter cartridges. Check the sweep of the workpiece when rotated and its mass together with the hanger. For a typical batch, compare how parts are loaded and the space required to replace the cartridges.
Wagner
Price on request
Spray wall · 3 cartridges · 6 kW · CE / ATEX
Wagner BASIC 8000 powder spray wall for larger parts
The Wagner BASIC 8000 is a powder spray wall for manually coating larger workpieces, including parts fed on a manual conveyor. The open working front leaves room to position panels or frames ahead of the filter section. Wagner lists three filter cartridges. Check how the largest part is positioned and whether the operator can reach the required areas. Confirm the conveyor interface and service space around the wall.
Wagner
Price on request
Manual booth · 3 cartridges · 2.2 kW · multi-colour
Wagner ID manual suspension booth for powder coating
The Wagner ID suspension booth is designed for small batches in different colours. A roof-mounted hook holds the part in the working area, and the stainless steel floor and smooth interior are accessible for cleaning. Measure from the hook to the lowest point of the workpiece and check how a batch is changed over. Confirm the powder collection arrangement and filter service clearance in the quotation.
Wagner
Price on request
Spray wall · 3 cartridges · 2.2 kW
Wagner ID powder spray wall for large workpieces
The Wagner ID spray wall serves larger workpieces in long single-colour runs and when shades change frequently. A stainless steel base is part of the working area. Check how panels are fed to and removed from the wall, and where the operator stands to reach their edges. Compare access to the cartridges and the cleaning sequence using the colours your shop actually alternates.
Wagner
Price on request
Compact automatic booth for frequent colour changes
Gema MagicCompact EquiFlow BA04 automatic powder booth MagicCompact® EquiFlow® BA04
MagicCompact EquiFlow BA04 is an automatic Gema booth for lines that alternate between colours. The plastic-panel enclosure and extraction arrangement are designed around cleaning between runs. Supply the part envelope, gun positions and number of colour changes per shift. Specify the powder centre in the quotation and trial the complete changeover with two contrasting powders.
Gema
Price on request
Pre-configured automatic booth for quick colour changes
Wagner QuickCube automatic powder booth for fast colour changes
The Wagner QuickCube is an automatic plastic booth for lines with frequent colour changes. Wagner offers four preconfigured sizes and modular manual positions for coating ahead of or after the automatic zone. Supply the suspended part envelope, gun count and areas requiring manual access. Check how the selected size connects to powder feed, conveyor handling and the changeover cleaning sequence.
Wagner
Price on request
Compact filter booth for small and medium shops
ROMER WP powder coating booth with cartridge filters
ROMER WP is a compact booth range for manual powder application. Cartridge filters collect overspray, Romer Jet cleans the filters and a touchscreen provides booth controls. Compare the WP-3, WP-4, WP-6 and WP-8 by booth size and filter count. To size a booth for your station, specify the widest part, the number of guns in simultaneous use and the clearance available for cartridge service.
ROMER
Price on request
Antistatic plastic booth for automatic lines
Vogamakina fast colour change plastic powder coating booth
Vogamakina designed this plastic booth for automatic coating with frequent colour changes. Antistatic panels and cleaning provisions near the booth floor are part of the manufacturer's described build. Share the number of colours, daily changeovers and longest run when sizing the system. Request a demonstration covering the booth, cyclone and powder centre as one cleaning sequence. Specify which guns, controls and recovery components the line requires.
Vogamakina
Price on request
Through-feed booth with cyclone reclaim for continuous lines
COLO through-feed powder coating booth with cyclone recovery
The COLO through-feed booth is intended for a line where suspended parts enter and leave at opposite ends. A cyclone separates powder from the extraction stream for collection and return according to the line configuration. The layout suits recurring runs of profiles, frames and panels. Specify the largest loaded hanger, carrier pitch and conveyor speed when sizing the booth. Agree on how recovered powder is handled when a different colour enters production.
COLO
20 000 $ (≈ 17 872 €) · for 1 piece

Powder guns and units

Manual electrostatic units with box feed, hopper or mini cup – from budget Chinese sets to Swiss and German reference units.

Mini unit · small hopper · 100 kV
COLO-668T-B portable powder coating kit for small jobs
The COLO-668T-B is a portable manual system with a small fluidising powder cup. It suits colour samples, trial parts and one-off jobs that use limited quantities of powder. Compare how often the cup will need refilling and how it is cleaned between colours. Send a representative part and the intended powder for a trial, and confirm the nozzles and accessories supplied with the gun.
COLO
Price on request
Manual unit · hopper or box feed · 100 kV
COLO-191S manual electrostatic powder coating unit
The COLO-191S is a manual electrostatic unit for shops coating a mix of part shapes. The operator can select settings for flat faces, recessed features and recoating to suit the controller and powder. Confirm the exact variant when comparing quotes, since the family is offered with several feed arrangements. Share a representative part with inside corners and ask which nozzles, hoses and gun wear parts are included.
COLO
from 1 050 $ (≈ 938 €) · per unit, delivery not included
Manual unit · 10 lb stainless hopper
COLO-191ST-H compact powder coating unit with 10 lb hopper
The COLO-191ST-H is a compact manual system with a hopper rated by the manufacturer at 10 lb. Hopper feed fits small recurring batches in one colour. State average powder use per batch and the number of consecutive parts when comparing configurations. Confirm the fluidisation equipment, hopper cleaning access and availability of injector and gun wear parts. Check the available space around the intended workstation.
COLO
Price on request
Manual unit · box feed · 7" touch panel
COLO-200S-B touchscreen powder coating unit with box feed
The COLO-200S-B is a manual touchscreen unit that feeds from the original powder box. This configuration suits orders with several colours in one shift. Ask to see the box change and the cleaning sequence for the injector, hose and gun. Confirm that your powder packaging fits the feed arrangement and that the quoted equipment covers it. For a trial, compare coverage on a flat face and an inside corner.
COLO
Price on request
Manual unit · stainless hopper · 7" touch panel
COLO-200S-H touchscreen powder coating unit with hopper
The COLO-200S-H combines touchscreen control with a separate powder hopper. It fits repeat workpieces coated in longer single-colour runs. Size the hopper to a typical batch and confirm how it is refilled and emptied. Check the fluidisation equipment and access to the injector. For an application trial, provide the powder type, part orientation and surfaces where even coverage matters.
COLO
Price on request
Manual unit · box feed · 100 kV
Vogamakina VG1E-VN manual powder coating unit with box feed
The Vogamakina VG1E-VN is a manual unit for shops that change colours frequently. The original box sits on a vibrating platform and an injector feeds powder to the gun. A wheeled stand lets the unit move to the working position. During a trial, time the exchange of two boxes you actually use and review how the powder path is cleaned. Confirm box fit, compressed-air requirements and supplied nozzles.
Vogamakina
2 600 € (≈ 2 910 $) · net, delivery not included
Manual unit · 0–100 kV · 250 g gun
Elektrosprey manual electrostatic powder coating gun set
The Elektrosprey manual set applies electrostatic powder in a spray booth. It suits jobs where the operator works around several faces and edges of each part. Describe the powder, typical batch and frequency of colour changes. Check the included gun, controller, feed equipment and nozzles. Request a trial on a recessed part and a list of replacement consumables.
Elektrosprey
Price on request
Manual unit · box feed · 7" touch · 100 kV
ROMER ProfiSpray V Manual Powder Coating Unit
The ProfiSpray V is a manual powder applicator with box feed and a 7-inch control panel. This configuration suits a shop running short batches and frequent colour changes. On a frame with recessed corners, check film build on both the open faces and the recesses. Use the production powder and hanger for the trial. Time cleaning from the last part in the old colour to the first acceptable part in the next one. Confirm which nozzles and changeover accessories are included.
ROMER
Price on request
Manual unit · box feed · 110 kV
Gema OptiFlex Pro B manual box-feed powder coating unit OptiFlex® Pro B
The Gema OptiFlex Pro B is a manual unit fed from the original powder box. It fits small orders that alternate among several colours during the day. In a demonstration, change between two packages you use and review cleaning access to the suction tube, injector and hose. Confirm box fit and the nozzles needed for the parts you coat most often.
Gema
Price on request
Manual unit · 50 l hopper · 110 kV
Gema OptiFlex Pro F manual powder coating unit with 50 L hopper OptiFlex® Pro F
The Gema OptiFlex Pro F feeds from a 50 L fluidising hopper. It suits longer manual runs in one colour and batches with higher powder consumption. Specify typical powder use per batch and how the container will be refilled. Review hopper cleaning and test feed consistency with the powder you normally run.
Gema
Price on request
Manual unit · box feed · colour change in 35 s
Gema OptiFlex Pro Q manual powder unit for fast colour changes OptiFlex® Pro Q
The Gema OptiFlex Pro Q is designed for manual coating with frequent changes between short colour runs. Time the trial from the last part in the first colour to the first acceptable part in the next. That includes powder-path cleaning and work in the booth. Confirm the compressed-air connections and accessories supplied with the quoted build.
Gema
Price on request
Manual unit · 40 l hopper · 100 kV · up to 400 g/min
Gema OptiFlex GO manual powder coating unit OptiFlex® GO
The Gema OptiFlex GO is a manual unit for a shop coating varied parts at one workstation. Trial it on flat brackets and a part with an inside corner to assess access with the gun. Confirm the feed arrangement for the quoted version and the supplied nozzles. Ask for the gun and injector consumables suited to your workload.
Gema
Price on request
Manual unit · box feed · PEM-X1
Wagner Sprint 2 B manual powder coating unit with box feed
The Wagner Sprint 2 B is a manual unit with original-box feed and the PEM-X1 gun. It fits shops handling orders in several colours that need to move quickly to the next box. Trial a change between two of your powders and check access to the injector and hose. Give the supplier your usual box size and confirm the included nozzles and functions of the WACON Sprint 2 XE controller.
Wagner
Price on request
Manual unit · 60 l container · PEM-X1
Wagner Sprint 2 H manual powder coating unit with 60 L hopper
The Wagner Sprint 2 H is a manual unit with a 60 L stainless steel powder container and a PEM-X1 gun. The container suits consecutive batches in one colour where the operator uses a larger quantity of powder per run. Check refilling, fluidisation and container cleaning when selecting the unit. Describe a typical batch and the frequency of colour changes so supply, equipment and nozzles can be specified for the application.
Wagner
Price on request
Manual unit · box feed · Expert control
Wagner Sprint 2 Expert B manual box-feed powder coating unit
The Wagner Sprint 2 Expert B pairs original-box feed with WACON Sprint 2 Expert control. It suits manual jobs that change colours and part shapes while requiring repeatable settings. The Wizard and Digital Surface Optimizer assist with selecting and adjusting settings for the application. Supply a representative part and coating target for the trial. Specify the process records you need and confirm the interfaces and measurement options in the quote.
Wagner
Price on request
Manual unit with 60 l container and touchscreen control
Wagner Sprint 2 Expert H manual powder unit with 60 L hopper
The Wagner Sprint 2 Expert H feeds from a 60 L container and uses WACON Sprint 2 Expert control. This fits longer runs of recurring parts where coating settings and process data need to be retained. In a trial, compare coverage on flat faces and more complex areas with your normal powder. Confirm the equipment for tracking consumption, the links to documentation systems and the accessories needed for your parts.
Wagner
Price on request

Powder curing ovens

Batch and tunnel ovens that cure the powder at 160–220 °C – electric, natural gas / LPG, diesel or infrared. Compare working size, heating power and what the price includes.

Batch oven · electric 6.5 kW
COLO-1688 compact electric powder curing oven
The COLO-1688 is an electric batch oven for curing powder on small runs of brackets, hardware and housings. COLO lists working dimensions of 1000 × 845 × 1600 mm in width, depth and height. A fan circulates air through the chamber. Check the height of the tallest hung part and the clear opening needed to load it. Provide your site supply and typical batch mass when requesting a configuration.
COLO
2 430 $ (≈ 2 171 €) · per unit, delivery not included
Batch oven · electric 18 kW
COLO-1515 electric powder curing oven with 1.5 m cube chamber
The COLO-1515 is an electric oven with 1500 × 1500 × 1500 mm working dimensions. Its cubic chamber gives flexibility in how compact rims, grilles and housings are arranged. Space the parts so air can circulate through the load. Ask for the clear door opening, hanging layout and electrical requirements for your site. Match the useful oven envelope to the booth and carrier before selecting a complete setup.
COLO
Price on request
Batch oven · electric 18 kW · trolley
COLO-1864 electric powder curing oven with loading trolley
The COLO-1864 electric build with trolley loading handles batches of enclosures, frames and bulky parts. COLO publishes a chamber of 1600 × 1400 × 1800 mm in width, depth and height for the electric model. The trolley lets the batch be arranged outside the oven. Confirm the frame dimensions, payload and rail or wheel layout. Check the connected electrical load and the space needed in front of the door.
COLO
Price on request
Batch oven · electric 40 kW · top track
COLO-2447 batch powder curing oven with overhead track
The COLO-2447 is a batch oven for curing powder on suspended workpieces. With a coordinated track layout, the same carrier can transfer parts from the spray station into the oven. It suits batches of frames and panels of varying heights. Verify clearance below the track, carrier length and the door arrangement around the suspension. When adding the oven to an existing shop, provide the rail interface and current carrier drawing.
COLO
Price on request
Batch oven · electric 54 kW · 4.5 m
COLO-1645 electric powder curing oven with 4.5 m working depth
The COLO-1645 is an electric batch oven for long profiles and frames. COLO lists a 1500 × 4500 × 1650 mm chamber in width, depth and height. Allow for the carrier and clearances around the part when sizing the batch. Plan a straight approach for loading and unloading long parts through the door. Provide maximum batch mass, available supply and the fixture arrangement for a comparable quotation.
COLO
Price on request
Batch oven · gas / LPG · Riello burner
COLO-3210 gas powder curing oven with 3.1 m working depth
The COLO-3210 gas oven is intended for batches of panels and mid-length welded parts. The catalogue working envelope is 2000 × 3100 × 1900 mm in width, depth and height. Use loaded carrier dimensions and the desired time between batches when sizing the equipment. Confirm the gas type, connection and burner maintenance access. Compare quotes on usable chamber size, batch mass and the proposed loading system.
COLO
Price on request
Batch oven · gas · 6 m · two trolleys
COLO 20 ft gas powder curing oven for long parts
The COLO 20 ft gas batch oven is designed for long profiles, fence sections and frames. The manufacturer lists a 6 m working depth and a loading trolley for the catalogue build. Check the carrier length, approach to the door and space needed to withdraw a full batch. Include site fuel, batch weight and required working height so the supplier can quote the appropriate configuration.
COLO
Price on request
Batch oven · gas / LPG / diesel · 3 × 3 m
COLO floor-level walk-in powder curing oven
This COLO walk-in oven is built for loading at shop-floor level. It suits trolley handling of heavy frames or bulky parts into the chamber. Confirm the threshold detail, foundation requirements and wheel loading for the proposed installation. Provide the loaded trolley mass and clear dimensions along its route. Request an installation drawing showing the usable entrance and door arrangement so the oven can be planned with the booth and staging area.
COLO
Price on request
Batch oven · electric, gas or diesel · made to size
Vogamakina box-type powder curing oven
The Vogamakina box oven cures powder on complete batches. The manufacturer describes forced air circulation and builds matched to the heating source. Its batch format allows different products to be scheduled around their respective requirements. Specify the largest load, working chamber dimensions, site power or fuel and how carriers enter the oven. Ask for temperature distribution data under a representative load.
Vogamakina
Price on request
Tunnel oven · conveyor · electric, gas or diesel
Vogamakina tunnel oven for continuous powder curing
The Vogamakina tunnel oven cures conveyor-borne workpieces by convection. Heated length is designed with conveyor speed and the time the part needs to reach and hold the temperature specified for its powder. Provide part mass, thickness and carrier spacing for the project. Confirm entry and exit openings, heating source and how the part temperature profile will be checked with the line loaded.
Vogamakina
Price on request
Infrared · catalytic gas or electric
Vogamakina industrial infrared oven for coating lines
The Vogamakina infrared oven is a heating module for coated parts in a continuous line. Emitter placement is planned around the surfaces to heat and the travel speed. For recessed shapes or parts with varying mass, supply samples to check the metal temperature profile. Establish whether the module will gel the coating ahead of a convection zone or serve another project function. Confirm working width, power supply and zone controls.
Vogamakina
Price on request
Batch oven · electric 3–150 kW · made to size
Elektrosprey electric box-type powder curing oven
The Elektrosprey electric box oven cures powder in batches. Select working volume around parts, carriers and the spacing within a load. Specify the largest batch, loading arrangement and available electrical supply. Ask for temperature distribution data with a loaded chamber and check manoeuvring room in front of the door.
Elektrosprey
Price on request
Continuous oven · natural gas / LPG · 50 000–500 000 kcal/h
Elektrosprey gas powder curing oven with overhead pallet transport
The Elektrosprey gas oven carries parts on pallets through the curing zone. It suits workpieces processed on fixtures with defined support points. Specify loaded pallet dimensions, maximum mass and feed direction. Review the loading area, fixture contact with the coated part and the quoted gas connection requirements.
Elektrosprey
Price on request
Batch oven · electric · forced circulation
ROMER SL Electric Powder Curing Oven
The SL is an electric oven for curing powder coatings. Chamber airflow and the programmable temperature cycle let the shop set a recipe for the workpiece and powder. For fence panels, specify the usable envelope with the trolley or hanging system in place. Thin slats and heavier frames warm at different rates in a mixed load. Assess part-metal temperature against the coating specification. Request the connected electrical load and a heat-up trace for representative parts. Confirm whether the data logger and chamber divider are included.
ROMER
from 8 200 € (≈ 9 177 $) · net
Batch oven · natural gas / LPG / oil · 240–460 mm insulation
ROMER SW Burner-Heated Powder Curing Oven
The SW is a burner-heated oven for curing powder coatings. ROMER describes gas and oil configurations selected for the plant and chamber size. For batches of steel frames, compare the complete cycle with the same load. Account for heat-up after loading, the time the parts spend within the powder's cure window and idle time between batches. Confirm the fuel, burner rating and exhaust provisions for the proposed installation. Ask for a trial-cycle record using the intended loading pattern.
ROMER
from 60 500 € (≈ 67 706 $) · net
Batch oven for long parts, Riello burner
COLO-5219 gas or diesel batch powder curing oven
The COLO-5219 is a batch oven for curing powder on long metalwork. Select the gas or diesel build around the fuel available on site and the load of a typical batch. Size the chamber around the part together with its trolley or hanging fixture. Obtain the specified burner type, usable length and maintenance clearances in writing so quotes describe the same configuration.
COLO
Price on request